HP XP20000/XP24000 구성 매뉴얼 - 페이지 27

{카테고리_이름} HP XP20000/XP24000에 대한 구성 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HP XP20000/XP24000 44 페이지. Hp storageworks xp disk array configuration guide: vmware (a5951-96106, september 2010)
HP XP20000/XP24000에 대해서도 마찬가지입니다: 릴리스 노트 (13 페이지), 통합 매뉴얼 (29 페이지), 릴리스 노트 (4 페이지), 관리자 매뉴얼 (50 페이지), 구성 매뉴얼 (42 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (36 페이지), 구성 매뉴얼 (36 페이지), 구성 매뉴얼 (30 페이지), 구성 매뉴얼 (36 페이지), 릴리스 노트 (5 페이지), 구성 매뉴얼 (46 페이지), 구성 매뉴얼 (46 페이지), 참조 매뉴얼 (46 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (38 페이지), 구성 매뉴얼 (34 페이지), 구성 매뉴얼 (30 페이지), 구성 매뉴얼 (30 페이지)

페이지 인쇄
HP XP20000/XP24000 구성 매뉴얼

3 Troubleshooting

This section includes resolutions for various error conditions you may encounter.
If you are unable to resolve an error condition, ask your HP support representative for assistance.

Error conditions

Depending on your system configuration, you may be able to view error messages (R-SIMS) as follows:
In XP Remote Web Console (Status tab)
In P9000 or XP Command View Advanced Edition Software (Alerts window)
Table 3 Error conditions
Error condition
The logical devices are not recog-
nized by the host.
The host does not reboot properly
after hard shutdown.
Physical volumes cannot be created.
Logical volumes cannot be created.
A file system is not mounted after re-
booting.
The disk array performs a self reboot
because the disk array was busy or
it logged a panic message.
The disk array responds "Not Ready"
or the disk array has displayed "Not
Ready" and timed out.
Recommended action
Verify the following:
The READY indicator lights on the disk array are ON.
Fiber cables are correctly installed and firmly connected.
The TIDs/WWNs on each bus are unique. Do not install two
devices with the same ID on the same bus. Recheck the buses for
new devices.
The maximum number of LUSE devices per port has not been ex-
ceeded.
The disk array host mode is set correctly.
If you power off the host without executing the shutdown process, wait
three minutes to allow the disk array's internal timeout process to purge
queued commands. If the host restarts while the disk array is processing
queued commands, the host may not reboot successfully.
Verify that the disk array logical devices are correctly formatted.
Verify that the volume capacity for OPEN-x volumes is not greater than
the maximum capacity allowed. See .
Verify that the capacity of the volume group is not less than the total
capacity of the partitioned logical volume.
Verify that the host was restarted correctly.
Verify that the file system attributes are correct.
Reboot the host.
Contact HP.
XP Disk Array Configuration Guide: Novell NetWare
27