Panasonic PT-AE1000 사용 설명서 - 페이지 8

{카테고리_이름} Panasonic PT-AE1000에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-AE1000 28 페이지. Panasonic lcd projector operating instructions
Panasonic PT-AE1000에 대해서도 마찬가지입니다: 사용 설명서 (28 페이지)

페이지 인쇄

You can adjust the projection size with 2.0 power zoom lens Calculate

a r

uum lens, calculate and define the throw distance as follows.

Diagonal length

(SD)

1.01 m

(40")

Projection size (16 : 9)

Screen height (SH)

Screen width (SW)

Throw distance (L)

Minimum distance

Maximum distance

(LW)

"T 2 m (3'11")

To^mzit)

ry^isTn-r

—)

_(L62 m

(2)

lT~m

(3tT

15m M'ir\-T

1.52 m

(60")

0 75 m

i2'5"l

(';■) "—tttttt---—

—

777

---———sTJ_1'33m

(44)

18m (5'10")

3 1

^TssTn

(5T)

j~^T(^)-T-

_<?°_>_ZH^LJ3^

^77^75^

JTTTTrn-

-4^LJ^l____J;12m

(3'8")

Y99m

(6TT)

-FT

—TTl1 — T>CO___Y247ri-

22Am

(7T)

-stTHTT-£

-Him (4'10'^_Zf^m

(Tr)

TTTTT-71

_187_m

(6'1")

-~a32^(To^)-TTTT^-£

r^3^rTT4^)

rTo^rTio^-ui

measurements above are approximate and may differ slightly from the actTTTTTTTT

■ Calculation methods for screen dimensions

You can calculate more detailed screen dimensions from the screen diagonal

SW=SDx 0.872

SH = SDx 0.490

0.87 m (2'10")

TOO m

(3'3")

1.12 m T3'8")

1.24m

(4j~

1.49 m (4'10")

1.87 m

(6'1 ")

(8'2")

3.0 m (9'10")

_ 3,6 m (11 '9")

~42 m (13TT

TTTTTT

~54 m (iTT

Tom (19'8")

TTtTTTT

T0m~(29'6")""

Tb m (394")™

LW= 1.189 xSD-0.04

LT = 2.378 xSD- 0.05

Unit: m

ie results above are approximate and may differ slightly from the actual measurements.

usff theProjector at a raised or a horizontally tilted position as it may

-ause malfunction of the projector,

Vlake sure the projector lens surface is parallel with the screen You can tilt

he projector body approximately ± 30° vertically. Overtilting may result in

shortening the component's life.

^ resun in

ooml^lr:*1: °lthe PJ°'iection ima9e' insta» a screen where sun light or

Sto SthelSts

y 0,1,0,heSCreen' Cl0Se Wlnd0WShadesor

Setting up

Projection method

projecting from front

projecting from rear

INSTALLATION: FRONT/DESK

| Mounting in the ceiling and

projecting from front

INSTALLATION: REAR/DESK

■ Mounting in the ceiling and

projecting from rear

INSTALLATION: FRONT/CEILING

INSTALLATION: REAR/CEILING

NOTE:

• A translucent screen is required for

REAR

projection.

• When mounting the projector in the ceiling, the optional ceiling mount bracket (ET-PKX100, ET-PKE1000S)

is required.

Front leg adjuster and throwing angle

You can adjust the throwing angle by screwing the front legs up/down.

This adjust the angle of the projector. See "Positioning the image" on page 21

NOTE:

• Heated air comes out of the

Air exhaust port.

Do not touch the

Air exhaust port

directly

• If keystone distortion occurs, see "KEYSTONE" on page 36,

You can use the projector with any of the following 4 projection methods. To set the desired method in the projector,

see "INSTALLATION" on page 39.