Panasonic PT-AE4000E 기능별 지침 - 페이지 21
{카테고리_이름} Panasonic PT-AE4000E에 대한 기능별 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-AE4000E 50 페이지. Full high-definition home cinema projector
Panasonic PT-AE4000E에 대해서도 마찬가지입니다: 사용 설명서 (36 페이지), 기능별 지침 (50 페이지), 브로셔 및 사양 (6 페이지)
페이지 인쇄
COLOUR TEMPERATURE
You can adjust the white balance of the projected image.
Less
bluish
Setting range: −6 to +6
DYNAMIC IRIS
You can switch automatic adjustment of the lamp and
the lens iris on/off.
ON:
Automatic adjustment
OFF:
No adjustment
WAVEFORM MONITOR
You can monitor whether or not the luminance level
of the input signal is in the recommended range by
displaying it in the waveform monitor. If the waveform
is not in the recommended range, adjust it for the
best quality. See "Adjusting the signal condition with a
waveform" on page 14.
OFF
FULL SCAN(Y)
FULL SCAN(R)
FULL SCAN(G)
FULL SCAN(B)
SINGLE LINE SCAN(Y)
SINGLE LINE SCAN(R)
SINGLE LINE SCAN(G)
SINGLE LINE SCAN(B)
MONITOR POSITION
AUTO ADJUST
1.
Press ▲ ▼ to move to the required waveform
style.
2.
Press the
ENTER button to select.
The WAVEFORM MONITOR will be displayed.
NOTE:
•
When the
WAVEFORM MONITOR is set to OFF, the
AUTO ADJUST is not displayed.
•
The waveform of the
WAVEFORM MONITOR will
not be displayed correctly with a noisy equipment or
source.
•
The
WAVEFORM MONITOR adjusts the signal level
based on the reference signal which consists of 0 %
and 100 %. The over scanned reference signal which
runs off the edge of the screen, below 0 % or over
100 % signal level will not be adjusted correctly.
MONITOR POSITION
J
When the FULL SCAN is selected, press ▲ ▼ ◄
► to adjust the position of the monitor.
See "Adjusting the signal condition with a waveform"
on page 14.
J
BLACK LEVEL ADJUST
More
Adjust the black level of luminance (Y) to 0 %.
WHITE LEVEL ADJUST
bluish
Adjust the white level of luminance (Y) to
100 %.
RGB ADJUST (BLACK)
Adjust the black level of colours (R/G/B) to 0 %.
RGB ADJUST (WHITE)
Adjust the white level of colours (R/G/B) to
100 %.
1.
2.
3.
4.
5.
J
UPPER LEFT
AUTO ADJUST
You can switch on/off the automatic adjustment
system in each item.
Press ▲ ▼ and select the required item.
Press ◄ ► and switch on/off.
Press ▲ ▼ and select
START AUTO ADJUST
and press the ENTER button.
The confirmation screen will be displayed.
Press ◄ ► and select
OK.
Press the
ENTER button.
Adjustment example
Project a commercial test signal for picture
adjustment on the screen and press the
WAVEFORM MONITOR button.
100%
50%
0%
ENTER
ENTER
Adjust to 100 %
100%
50%
displayable area
0%
Adjust to 0 %
Monitor position
With COMPUTER (except HD) or
HDMI (Expand)
Adjust to 100 %
100%
50%
displayable area
0%
Adjust to 0 %
Monitor position
PICTURE menu
ON
ON
OFF
OFF
Image
Image
E
NGLISH - 21