Panasonic PT-AE500 사용 설명서 - 페이지 22
{카테고리_이름} Panasonic PT-AE500에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-AE500 30 페이지.
페이지 인쇄
Option settings
Press the F or G button to select
an item, and then press the I or H
button to change the setting.
O P T I O N
O S D
O N
N R
O N
P C P R I O R I T Y
N O R M A L
B A C K C O L O R
B L A C K
E D I D
E D I D 1
F R O N T / R E A R
F R O N T
D E S K / C E I L I N G
D E S K
F A N C O N T R O L
N O R M A L
L A M P P O W E R
H I G H
L A M P R U N T I M E
5 H
S E L E C T
A D J
E S C
OSD
O S D
O N
[
O F F
ON
The signal name is displayed
in the top-right corner of the
screen when the input signal
is changed.
OFF Use this setting when you do
not want the signal name to
be displayed.
Noise Reduction (NR)
(YP
P
only)
B
R
N R
O N
[
O F F
If noise occurs from the projector
because of a poor input signal, set
"NR" to "ON".
To turn off the "NR" feature, set it to
"OFF".
42-E
NGLISH
PC PRIORITY
(PC only)
P C P R I O R I T Y
N O R M A L
[
W I D E
NORMAL The PC screen data is
displayed in a 4:3
aspect ratio.
WIDE
The PC screen data is
displayed in a 16:9
aspect ratio.
BACK COLOR
B A C K C O L O R
B L A C K
[
B L U E
This sets the color which is projected
onto the screen when no signal is
being input to the projector.
EDID
(DVI only)
E D I D
E D I D 1
[
E D I D 2
When DVI signals such as 525p,
625p, HDTV60, HDTV50, or 750p
signals are being input, set to
"EDID1". Set to "EDID2" when other
signals are being input.
NOTE:
B "EDID" stands for "Extended
Display Identification Data". It
is used to transmit information
such as the model name of this
projector or the settings to the
computer connected to DVI-D
IN connector. This is useful for
projecting the images with the
proper resolution.
FRONT/REAR
F R O N T / R E A R
F R O N T
[
R E A R
This setting should be changed in
accordance with the projector
setting-up method. (Refer to page 16.)
FRONT When the projector is
placed in front of a screen.
REAR
When using a translucent
screen.
DESK/CEILING
D E S K / C E I L I N G
D E S K
[
C E I L I N G
This setting should be changed in
accordance with the projector
setting-up method. (Refer to page 16.)
DESK
When the projector is
placed on a desk or
similar.
CEILING When the projector is
suspended from a ceiling
using the ceiling bracket
(sold separately).
FAN CONTROL
F A N C O N T R O L
N O R M A L
[
H I G H
Set "FAN CONTROL" to "HIGH",
when using this projector at high
elevations (above 1 400 m) only.
LAMP POWER
L A M P P O W E R
H I G H
[
L O W
This setting changes the lamp
brightness. When set to "LOW", the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced.
The "LOW" setting is recommended
for narrow rooms where a high
picture luminance is not essential or
for watching movies.
NOTE:
B "LAMP POWER" cannot be set
when no signal is being input.
LAMP RUNTIME
This setting displays the usage time
for the lamp unit which is currently
being used. When replacing the
lamp unit, follow the instructions on
page 48, and reset "LAMP
RUNTIME" to "0".
NOTE:
B The lamp's operating life varies
depending on the usage
conditions (such as the "LAMP
POWER" setting and the
number of times the power is
turned on and off).
E
-43
NGLISH