Panasonic PT-L6510E 사용 설명서 - 페이지 13
{카테고리_이름} Panasonic PT-L6510E에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-L6510E 50 페이지. 3600 ansi lumens sxga lcd projector 4200 ansi lumens xga lcd projector
Panasonic PT-L6510E에 대해서도 마찬가지입니다: 브로셔 및 사양 (6 페이지)
페이지 인쇄
< Interface panel >
S-VIDEO IN
R/R-Y/P
R
S-VIDEO IN port (pages 19, 20 and 33)
Connect an S-video signal source to this port.
Depend on input signal, screen aspect will
automatically change 16:9 or 4:3.
VIDEO IN port (pages 20 and 22)
Connect a composite video signal source to this port.
(BNC)
VIDEO OUT port (pages 20 and 22)
Composite video signal appears at this port. (BNC)
AUDIO IN L-R jacks (page 20)
Only a single pair of audio inputs is available. Change
connections to these jacks according to your choice
of video source from composite and S-video (RCA
jacks).
RGB AUDIO IN jack (pages 20 and 21)
Only a single pair of audio inputs is available. Change
connections to these jacks according to your choice
of video source from RGB1, RGB2 and DVI-D (M3
jacks).
AUDIO OUT jack (page 20)
The audio signals applied to the AUDIO IN or RGB
AUDIO IN jacks of this unit appear at this jack. Once
a cable is plugged into this jack, the signal lines to
the internal speakers are cut off. (M3 jack)
USB IN ports (pages 16, 21 and 38)
The remote control can be used as your PC mouse
by connecting the projector to your PC with the
supplied USB cable. (4-pin square connector)
USB OUT ports
The control ports on two or more projectors can be
connected to each other for interlocked control
operations. (Type B)
IN
OUT
L
R
IN
OUT
RGB
VIDEO
AUDIO IN
AUDIO AUDIO
G/Y
B/B-Y/P
SYNC/HD
VD
B
RGB 1 IN
IN
OUT
DVI-D
IN
OUT
IN
OUT
USB
SERIAL
RGB 2 IN
RGB OUT
REMOTE
> PC <
SERIAL IN port (pages 20, 21, 22 and 37)
Use the RS-232C serial port as an alternative
interface for controlling the projector from your PC.
(D-SUB 9 pin)
SERIAL OUT port (pages 21 and 22)
The signal applied to the serial input port appears at
this port (9-pin D-sub female connector).
RGB1 (YP
P
) input ports (pages 20, 21 and 22)
B
R
Apply RGB or YP
P
B
R
RGB2 (YP
P
) IN port (page 21)
B
R
RGB video input port. (D-SUB 15 pin)
RGB OUT port (pages 21 and 22)
The signals applied to RGB1 or RGB2 input ports
appear at this port (15-pin D-sub female connector).
REMOTE port (page 39)
This port may be used to control the projector from
the Remote Control set up in Wired mode. (9-pin D-
sub female connector)
DVI-D IN port (pages 19 and 21)
DVI-D signals are applied to this port. (24-pin DVI
connector)
DVI-D OUT port (page 21)
The signal applied to the DVI-D input port appears at
this port (24-pin DVI connector).
WIRED IN/OUT ports (page 17)
Use to connect multiple PT-L6510E/L6600E
projectors in a daisy chain to simultaneously control
them from a single wired remote control. (M3 jack)
IN
OUT
WIRED
TBMU152
video to these ports. (BNC)
13