Panasonic PT-L6600E 사용 설명서 - 페이지 18
{카테고리_이름} Panasonic PT-L6600E에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-L6600E 50 페이지. 3600 ansi lumens sxga lcd projector 4200 ansi lumens xga lcd projector
Panasonic PT-L6600E에 대해서도 마찬가지입니다: 브로셔 및 사양 (6 페이지), 브로셔 및 사양 (6 페이지)
페이지 인쇄
Setting-up
Projection Schemes
Any of the following four projection schemes can be
used with the PT-L6510E/L6600E projector
depending on user's needs or viewing conditions.
Use "OPTION 1" menu (chosen from the MAIN
MENU) to choose the appropriate projection scheme
(see page 34).
Table standing
(Default position)
Installation Geometry
After the projector is roughly positioned, picture size
and vertical picture positioning can be finely adjusted
with the powered zoom lens and lens tilt mechanism.
Side view
With optional ceiling mount
bracket (ET-PKL6500)
H
H
Screen
L: Projection distance
SH: Image height
SW: Image width
H: Distance from centre of lens to bottom
edge of projected image.
Top view
Screen
18
Projection Scheme 2
Ceiling mount
L
L
IN
IN
OUT
L
R
IN
OUT
IN
OUT
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO AUDIO
RGB
USB
SERIAL
IN
R/R-Y/P
R
G/Y
B/B-Y/P
B
SYNC/HD
VD
OUT
RGB 1 IN
RGB 2 IN
RGB OUT
REMOTE
WIRED
IN
DVI-D
OUT
> PC <
TBMU152
L
87.5
175
[unit : mm]
Projection Distances
Screen Size (4 : 3)
Diagonal length Height (SH) Width (SW) Wide (LW) Telephoto (LT)
0.76
0.46
1.02
0.61
1.27
0.76
1.52
0.91
2.03
1.22
2.54
1.52
3.05
1.83
3.56
2.13
4.06
2.44
4.57
2.75
5.08
3.05
5.51
3.35
6.10
3.66
6.60
3.96
7.11
4.27
7.62
4.57
Setting-up dimensions which are not given in the above
table can be calculated using the formulas below.
If the screen size (diagonal) is SD, then the following
formulas is first used to obtain the screen width (SW).
SW = (SD x 0.0254) x 4
The value for SW obtained above can then be used
with the following function to calculate the projection
distance for the wide lens position (LW) and the
projection distance for the telephoto lens position (LT).
LW = 1.831 x SW - 0.071
LT = 2.449 x SW - 0.066
For 16 : 9 aspect rations, the following formal can be
used to calculate the screen width (SW).
SW = (SD x 0.0254) x 16
Note
276
• The dimensions in the table above and the values
obtained from the above formulas may contain
slight errors.
• It is recommended that you use the projection
distance for the wide lens position (except in cases
where the diagonal picture size is 0.762 m).
• The above dimensions are the case when the
aspect ratio is 4:3. When an SXGA signal is input
and projected, the right and left ends of the picture
will be blanked the aspect ratio will be 5:4.
Projection distance: L
0.61
—
1.4
1.4
0.81
1.9
1.8
1.02
2.4
2.1
1.22
2.9
1.63
2.9
3.9
2.03
3.6
4.9
2.44
4.3
5.9
2.84
5.1
6.9
5.8
3.25
7.9
6.6
3.66
8.9
7.3
4.06
9.9
4.47
8.1
10.9
4.88
8.8
11.9
5.28
9.5
12.9
5.69
10.3
13.9
11.0
6.10
14.9
5 (SD unit is inches)
327
Unit : m
Height
position: H
0.02 to 0.22
0.03 to 0.30
0.04 to 0.38
0.05 to 0.45
0.06 to 0.60
0.08 to 0.76
0.09 to 0.91
0.11 to 1.06
0.12 to 1.21
0.14 to 1.37
0.15 to 1.52
0.17 to 1.67
0.18 to 1.82
0.20 to 1.98
0.21 to 2.13
0.23 to 2.28