Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls 사용 설명서 - 페이지 26
{카테고리_이름} Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls 33 페이지. Micro portable wireless xga lcd projector
Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls에 대해서도 마찬가지입니다: 사양 (4 페이지)
페이지 인쇄
When the TEMP indicator and the
LAMP indicator are illuminated
There are two indicators on the control panel of the projector which give
information about the operating condition of the projector. These indicators
illuminate or flash to warn you about problems that have occurred inside the
projector, so if you notice that one of the indicators is on, turn off the power
and check the table below for the cause of the problem.
LAMP indicator
TEMP indicator
TEMP indicator
Indicator
Illuminated (red)
display
(Lamp unit on)
The surrounding temperature or
the temperature inside the
projector has become unusually
Problem
high.
B The ventilation holes may be covered.
Possible
B The ambient temperature in the place of use may be too high.
cause
B The air filter may be blocked.
B Uncover the ventilation holes.
B Set up the projector in a place where the temperature is
between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is
between 20% and 80% (with no condensation). [If you set the
"FAN CONTROL" to "HIGH" (page 45), set up the projector in a
Remedy
place where the temperature is between 0 °C (32 °F) and 35 °C
(95 °F) and the humidity is between 20% and 80% (with no
condensation).]
B Disconnect the power cord by following the procedure on page
26, and then clean the air filter. (Refer to page 52)
50-E
NGLISH
Flashing (red)
(Lamp unit off)
The surrounding temperature or
the temperature inside the
projector has become
dangerously high, causing the
lamp unit to automatically shut
off.
LAMP indicator
Indicator
Illuminated (red)
display
It is nearly time to
An abnormality has been detected in the lamp
replace the lamp
circuit.
Problem
unit.
B Does "REPLACE
B The power may
LAMP" appear on
have been turned
Possible
the screen after
on straight away
cause
the projector is
after it was turned
turned on?
off.
B This occurs when
B Wait for a while
the operation time
until the lamp unit
for the lamp unit is
cools down before
nearing 1 800
turning the power
hours (when
back on again.
"LAMP POWER"
has been set to
Remedy
"HIGH"). Ask your
dealer or an
Authorized
Service Center to
replace the lamp
unit.
NOTE:
B Be sure to disconnect the power cord by following the procedure given
in "Turning off the power" on page 26 before carrying out any of the
procedures in the "Remedy" column.
B If the power turns off after the TEMP indicator has illuminated, it means
an abnormality has occurred. Please contact an Authorized Service
Center so that the necessary repairs can be made.
Flashing (red)
B There may be an
abnormality in the
lamp circuit.
B Disconnect the
power cord by
following the
procedure on
page 26, and then
contact an
Authorized
Service Center.
E
-51
NGLISH