Panasonic PT-LB10U - Mobile Projector XGA 2000 Lumens 사용 설명서 - 페이지 23
{카테고리_이름} Panasonic PT-LB10U - Mobile Projector XGA 2000 Lumens에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-LB10U - Mobile Projector XGA 2000 Lumens 33 페이지. Micro portable xga lcd projector
Panasonic PT-LB10U - Mobile Projector XGA 2000 Lumens에 대해서도 마찬가지입니다: 브로셔 및 사양 (4 페이지)
페이지 인쇄
AUTO SEARCH
This should normally be set to "ON"
ON
When the power is turned on and
"AUTO SETUP" is running, the
projector detects which signals are
being input and uses these signals
for projection.
(If a picture is being projected, the
signal source is not automatically
changed.)
OFF
Use this setting when you do not
want the signal source to be
changed automatically when the
power is turned on and "AUTO
SETUP" is running.
AUTO SIGNAL
This should normally be set to "ON".
ON
"AUTO SETUP" will be carried out
automatically when the input signal
is changed.
OFF
"AUTO SETUP" will not function
when the input signal is changed.
AUTO KEYSTN
This should normally be set to "ON".
ON
During "AUTO SETUP", the angle of
tilt of the projector is detected and
keystone distortion is corrected
automatically.
OFF
Use this setting when you do not
want automatic keystone correction
to be carried out during "AUTO
SETUP", such as when the screen
itself is at an angle.
44-E
NGLISH
RGB/YP
P
B
R
R G B / Y P
P
A U T O
B
R
[
R G B
[
Y P
P
B
R
This should normally be set to
"AUTO". RGB or YP
P
is selected
B
R
automatically depending on the
synchronising signal status.
When 480i, 576i, 480p, 576p,
1 080/60i, 1 080/50i, 720/60p and
some VGA480 signals are being
input, select "RGB" or "YP
P
" in
B
R
accordance with the input signal.
VGA60/480p
V G A 6 0 / 4 8 0 p
4 8 0 p
[
V G A 6 0
Set to "VGA60" when 59.9Hz
VGA480 signals are being input
(refer to page 60 for details). Set to
"480p" when 480p RGB signals are
being input.
SXGA MODE
S X G A M O D E
S X G A
[
S X G A +
This setting is only for an SXGA
signal.
SXGA
Select this item normally.
SXGA+
When the edges of the projected
image are not visible, select this
item.
Noise Reduction (NR)
(S-VIDEO/VIDEO only)
If noise occurs from the projector
because of a poor input signal, set
"NR" to "ON".
To turn off the "NR" feature, set it to
"OFF".
BLACKBOARD
(PT-LB10NTU/PT-LB10U/PT-
LB10SU/PT-LB10SVU only)
Set to "ON" when "PICTURE
MODE" is set to "BLACK-BD".
(Refer to page 37.)
BACK COLOR
B A C K C O L O R
B L U E
[
B L A C K
This sets the color which is
projected onto the screen when no
signal is being input to the projector.
FRONT/REAR
F R O N T / R E A R
F R O N T
[
R E A R
This setting should be changed in
accordance with the projector
setting-up method.
(Refer to page 19.)
FRONT
When the projector is placed in front
of a screen.
REAR
When using a translucent screen.
DESK/CEILING
D E S K / C E I L I N G
D E S K
[
C E I L I N G
This setting should be changed in
accordance with the projector
setting-up method.
(Refer to page 19.)
DESK
When the projector is placed on a
desk or similar.
CEILING
When the projector is suspended
from a ceiling using the ceiling
bracket (sold separately).
FAN CONTROL
F A N C O N T R O L
S T A N D A R D
[
H I G H
Set "FAN CONTROL" to "HIGH",
when using this projector at high
elevations (above 1 400 m) only.
LAMP POWER
L A M P P O W E R
H I G H
[
L O W
This setting changes the lamp
brightness. When set to "LOW", the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced. This can help to extend
the lamp's operating life. If using the
projector in small rooms where high
luminance is not required, it is
recommended that you set the
"LAMP POWER" to "LOW".
NOTE:
B "LAMP POWER" cannot be set
when no signal is being input.
E
-45
NGLISH