Panasonic PTDW8300U - DLP PROJECTOR 사양 - 페이지 16
{카테고리_이름} Panasonic PTDW8300U - DLP PROJECTOR에 대한 사양을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PTDW8300U - DLP PROJECTOR 17 페이지. Pt-dz8700 series 3-chip dlp projector
Panasonic PTDW8300U - DLP PROJECTOR에 대해서도 마찬가지입니다: 사양 (6 페이지)
페이지 인쇄
S
F
P
E
C
I
L
3-Chip DLP
®
Projector
Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1. Never place objects on top of the projector while it is operating.
2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector's
exhaust openings.
3. Do not stack projector units directly on top of one another. If two units must be stacked for back-
up use in ordinary projection, use a method as shown below and provide ample space between the
units to ensure that exhaust heat does not accumulate near the intake opening or around the units.
Dual stacked projection is not recommended.
4. Make sure that nothing blocks the projector's air intake and exhaust openings. Also, install the pro-
jector so that cool or hot air from other air conditioning equipment does not flow directly toward the
projector's air intake or exhaust openings.
5. Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed
space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the
intake opening. This may cause the projector's protective circuit to interrupt projector operation, or
may shorten the replacement cycle for the Auto Cleaning Filter (ACF) Unit.
6. If the projector is installed in an enclosed space, ensure that the temperature of the air surrounding
the projector is between 0°C (32°F) and 40°C (104°F). Also make sure that the projector's intake and
exhaust openings are not blocked. Even though the air surrounding the projector is 40°C (104°F) or
less, if hot exhaust air accumulates inside the space, it may cause the projector's protective circuit
to interrupt projector operation, or may shorten the replacement cycle for the ACF Unit. Pay particu-
lar attention to the surrounding temperature conditions when planning the installation.
7. If the projector is not to be set on the floor using adjuster legs, install it by using the five ceiling-
mount screw holes (screw diameter: M6, length of each screw hole in the projector: 8 mm (5/16˝)).
Provide a space of 5 to 10 mm (3/16˝ to 13/32˝) between the projector and the mounting surface by
inserting metal spacers.
500 mm (19-11/16 ˝ ) or more
LENS
MENU
VIDEO
ENTER
S-VIDEO
RGB1
AUTO
SHUTTER
SETUP
RGB2
DVI-D/HDMI
SDI
MENU
LENS
VIDEO
ENTER
S-VIDEO
RGB1
SETUP
AUTO
SHUTTER
RGB2
DVI-D/HDMI
SDI
Direction of air intake and exhaust
As of July 2010
SFD10M003
E
500 mm (19-11/16 ˝ )
or more
100 mm
( 3-15/16 ˝ )
or more
PT-DW8300U
500 mm (19-11/16 ˝ )
or more
MENU
LENS
VIDEO
ENTER
S-VIDEO
RGB1
AUTO
SETUP
SHUTTER
RGB2
DVI-D/HDMI
SDI
MENU
LENS
VIDEO
ENTER
S-VIDEO
RGB1
AUTO
SHUTTER
SETUP
RGB2
DVI-D/HDMI
SDI
Do not stack projector
units directly on top of
one another.
Intake
Exhaust
1 6 / 1 7