Panasonic PTLC56U - LCD PROJECTOR 사용 설명서 - 페이지 19
{카테고리_이름} Panasonic PTLC56U - LCD PROJECTOR에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PTLC56U - LCD PROJECTOR 37 페이지. Commercial use
Panasonic PTLC56U - LCD PROJECTOR에 대해서도 마찬가지입니다: 사양 (4 페이지), 사용 설명서 (32 페이지)
페이지 인쇄
BRIGHT
This adjusts the darker areas (black
areas) in the picture. Press the H
button if dark areas are too solid (for
example, if hair is difficult to see), and
press the I button if black areas are
too light (grey rather than black).
COLOR
(S-VIDEO/VIDEO/YP
P
only)
B
R
Press the H button to make the
color more vivid in tone, and press
the I button to make the color
more pastel in tone.
TINT
(NTSC/NTSC 4.43/YP
P
only)
B
R
This adjusts the flesh tones in the
picture. Press the H button to make
flesh tones more greenish, and
press the I button to make the
flesh tones more reddish.
SHARPNESS
Press the H button to make the
picture details sharper, and press
the I button to make the picture
details softer.
Color Hue Setting (color
temperature)
C O L O R T E M P .
S T A N D A R D
[
H I G H
[
L O W
This is used to adjust the white
areas of the picture if they appear
bluish or reddish.
WHITE BALANCE R/G/B
(RGB only)
This is used to adjust the white
areas of the picture if they appear
colorised. Press the I button to
make the selected color lighter.
36-E
NGLISH
Press the H button to make the
selected color stronger.
TV-SYSTEM
(S-VIDEO/VIDEO only)
T V - S Y S T E M
A U T O 1
[
A U T O 2
[
N T S C
[
N T S C 4 . 4 3
[
P A L
[
P A L - M
[
P A L - N
[
S E C A M
AUTO1
The projector automatically
distinguishes between NTSC/NTSC
4.43/PAL/PAL60/SECAM signals.
AUTO2
The projector automatically
distinguishes between NTSC/PAL-
M/PAL-N signals.
NOTE:
B This should normally be set to
"AUTO1" or "AUTO2". If the
signal is of such poor quality
that the correct format cannot
be automatically distinguished,
change the setting manually to
the required TV system.
STILL MODE
S T I L L M O D E
O F F
[
O N
To reduce flickering of still images (vertical
flicker), set "STILL MODE" to "ON" by pressing
the I or H buttons.
NOTE:
B Do not set "STILL MODE" to "ON" when
playing back moving images.
SIGNAL MODE
(RGB/YP
P
only)
B
R
This displays the type of signal which is
currently being projected.
Refer to the table on page 58 for details on
each type of signal.
Projecting sRGB-compatible
pictures
sRGB is an international color reproduction
standard (IEC61966-2-1) established by the
International Electrotechnical Commission
(IEC). If you would like the colors in sRGB-
compatible pictures to be reproduced more
faithfully, make the following settings.
# # Press the F F or G G button to select
"PICTURE MODE", and then use the I I
or H H button to select "NATURAL".
$ $ Press the STANDARD (STD) button on
the remote control unit.
% % Press the F F or G G button to select
"COLOR TEMP.", and then use the I I
or H H button to select "STANDARD".
NOTE:
B sRGB is only enabled when RGB
signals are being input (when LAMP
POWER has been set to "HIGH").
E
-37
NGLISH