Panasonic RX-D45 사용 설명서 - 페이지 6
{카테고리_이름} Panasonic RX-D45에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic RX-D45 8 페이지. Portable stereo cd system
Panasonic RX-D45에 대해서도 마찬가지입니다: 사용 설명서 (8 페이지), 사용 설명서 (20 페이지)
페이지 인쇄
Manual presetting
1
If "PGM" is displayed, press [TUNE MODE] to clear it.
2
Press [–/2] or [6/+] to select the frequency of the
required station.
3
Press and hold [–PGM].
"PGM" and the selected frequency blinks.
4
Within 10 seconds or so
Press [–PGM] followed by [–/2] or [6/+] to select
the desired channel.
5
Press [–PGM].
The station occupying a channel is erased if another station
is preset to that channel.
6
Repeat steps 2 to 5 to preset more stations.
Selecting a preset station
1
Press [TUNE MODE].
"PGM" is displayed.
2
Press [–/2] or [6/+] to select the channel.
AM allocation setting
AM allocation setting
This system can also receive AM broadcasts allocated in
10 kHz steps.
To change the step from 9 kHz to 10 kHz
1
Press and hold [8] (stop).
After a few seconds the display changes to a fl ashing
display of the current minimum frequency.
2
Continue to hold down [8] (stop).
• When the minimum frequency changes, release the
button. To return to the original step, repeat the above
steps.
• After the setting is changed, any previously preset
frequency will be cleared.
Cassette tape – Play and record
Basic play
Basic play
Use normal position tapes.
High position and metal position tapes can be played, but
the unit will not be able to identify the characteristics of these
tapes.
1
Press [TAPE/OFF].
2
Open the cassette operation buttons' lid.
3
Press [8/x, STOP/EJECT] and insert the cassette.
Insert with the side to be played facing up and the exposed
tape facing towards you. Close the deck by hand.
6
Preset channel
4
Press [4, PLAY] to start play.
Stop tape
Press [8/x, STOP/EJECT].
playback
Pause play
Press [9, PAUSE].
Press again to resume play.
Fast-
Press [3, REW/REV] or [5, FF/CUE] in
forward and
the stop mode.
rewind
Search for
Press [3, REW/REV] (to search backward)
a specifi c
or [5, FF/CUE] (to search forward) during
point
playback.
Play is resumed when the button is released.
Recording
Recording
Use normal position tapes.
High position and metal position tapes can be used, but the
unit will not be able to record or erase them correctly.
✒
Preparation
Wind up the source tape so recording can begin immediately.
1
Press [0, STOP/EJECT] and insert the cassette to
be recorded.
Insert with the side to be recorded facing up and the
exposed tape facing towards you.
2
Select the source to be recorded.
Radio
Tune in the station (Z page 5).
Disc
1. Insert the disc you want to record.
Press [4/9, CD] and then [8] (stop).
2. Prepare the desired disc recording mode.
Record programmed tracks
Program the tracks you want (Z page 4).
Record specifi c tracks
Press [·PLAY MODE] to select the desired
mode (Z page 4).
3
V
Press [
] to start recording.
Stop recording
Press [8/x, STOP/EJECT].
Record on the
Turn the cassette over and press [
other side of
the tape
Erase a
1. Press [TAPE/OFF].
recorded
2. Insert the recorded cassette.
sound
3. Press [
Your attention is drawn to the fact that recording pre-
recorded tapes or discs or other published or broadcast
material may infringe copyright laws.
✒
Note
Changes to volume and sound quality do not affect recording.
Erasure prevention
The illustration shows how to remove the tabs to prevent
recording. To record on the tape again, cover as shown.
To prevent recording
Side A
Tab for Side B
Tab for Side A
✒
Note
• Tapes exceeding 100 minutes are thin and can break or get
caught in the mechanism.
• Tape slack can get caught up in the mechanism and should
be wound up before the tape is played.
• Endless tapes can get caught up in the deck's moving parts
if used incorrectly.
V
V
].
To re-record
Adhesive tape
].