Panasonic RX-ES27 사용 설명서 - 페이지 14

{카테고리_이름} Panasonic RX-ES27에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic RX-ES27 40 페이지. Portable stereo cd system
Panasonic RX-ES27에 대해서도 마찬가지입니다: 사용 설명서 (40 페이지), 사용 설명서 (22 페이지), 사용 설명서 (40 페이지)

페이지 인쇄
Panasonic RX-ES27 사용 설명서
7
A
3
7
1
7
○
○
○
○
○
○
○
2
7
○
○
○
○
○
○
○
3
7
B
7
7
2
3
•
7
1
TUNER
7
○
○
○
○
○
○
○
2
AUTO SCAN
7
○
○
○
○
○
○
○
3
AUTO SCAN
7
C
FM MODE/BP
7
D
FM
Downloaded From Disc-Player.com Panasonic Manuals
14
7
7
1
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
7
PRESET EQ
TAPE
TUNER
CD
1
S.VIRTUALIZER
REW
FF
AUTO SCAN
PRESET TUNE
CD SKIP
–
VOLUME
+
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Indicates auto scan
!"#
wJOðUÄuðË_« ` *« 5³¹
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
FM MODE/BP
C RESET
RANDOM
REPEAT
PRESET EQ
TAPE
TUNER
CD
S.VIRTUALIZER
REW
FF
AUTO SCAN
PRESET TUNE
CD SKIP
VOLUME
AM

The Radio

2
Preparation: (when using batteries) Press [
A
Normal tuning
Press [TUNER BAND] to select "FM" or "AM".
1
(Unit comes on when using AC power.)
Each time you press the button:
AM ↔ FM
Press [ REW/–/Q
2
station.
"
Press [+, – VOLUME] to adjust the volume.
3
○
○
○
○
○
○
○
○
B
Using auto scan
Remote control only
You can search for a station by listening to all tuned-in stations for 8
seconds each.
Press [TUNER] to select "FM" or "AM".
1
○
○
○
○
○
○
○
○
Press [AUTO SCAN].
2
Auto scan starts.
Press [AUTO SCAN] when you find the desired
3
station.
Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].
C
If noise is excessive in FM
Remote control only
Press [FM MODE/BP] to display "
Monaural sound is selected ("
reception is weak.
Press [FM MODE/BP] again to cancel the mode.
Auto-tuning
Press and hold [REW / – / Q] or [R / + / FF] until the frequency
○
○
○
○
○
○
○
○
starts changing rapidly.
The frequency stops when it finds a station. (Interference may also
cause it to stop. Start auto-tuning again if this occurs.)
To stop auto-tuning
Press [REW / – / Q] or [R / + / FF].
D
To improve reception
FM: Change the length and direction of the antenna.
AM: Change the facing of the unit.
○
○
○
○
○
○
○
○
Note
• AM reception is briefly interrupted if [0 DECK] is pressed.
• To improve reception when using the unit in a building or vehicle,
use it near a window.
AM allocation setting
Only from the main unit
Before receiving AM broadcasts, be sure to select the correct alloca-
1
tion setting (either 9 kHz or 10 kHz) for your area.
2
Press [TUNER BAND] to select FM.
Press and hold [TUNER BAND] for approximately 5
seconds.
The frequency display will be returned to the minimum frequency
of the AM band and the display will begin to flash. Keep holding
3
for approximately 5 more seconds.
When the display stops flashing and indicates a
different frequency number, release [TUNER BAND].
To return to the original frequency, repeat steps
Note
After changing the "allocation" setting, the frequencies you
previously preset into the memory will be cleared.
Q ] or [ R
Q
Q
R /+/FF ] to select a
R
R
Q
R
" is displayed during FM stereo broadcasts.
MONO
".
" goes off) and noise reduces when
/I
].
1
3
to
above.