Panasonic RXD20 - RADIO CASSETTE W/CD 사용 설명서 - 페이지 3
{카테고리_이름} Panasonic RXD20 - RADIO CASSETTE W/CD에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic RXD20 - RADIO CASSETTE W/CD 9 페이지. Portable stereo cd system
Panasonic RXD20 - RADIO CASSETTE W/CD에 대해서도 마찬가지입니다: 사용 설명서 (9 페이지)
페이지 인쇄
Normal tuning
3 2 1
1
Switch [
] to "TUNER".
(Power comes on.)
2
Press [BAND] to select "FM" or "AM".
3
(Omit this step if using the remote control)
If "
" is on the display, press
[TUNE MODE] to clear it off .
Press [–/g] or [f/+] to
4
tune to the desired station.
The frequency changes one step
each time a button is pressed.
Automatic tuning
Keep [–/ g] or [f/+] depressed and release when the frequency
display starts to change. A station with good reception is automati-
cally selected and the process stops.
To stop automatic tuning, press [–/ g] or [f/+] again.
Note
Automatic tuning may stop on a frequency where there is no station if
there is interference. Press [–/ g] and [f/+] to tune if this occurs.
Adjust the volume.
5
To use auto scan
You can search for a station by listening to all tuned-in stations for 8
seconds each.
Preparation: Switch [
1. Press [BAND] to select "FM" or "AM".
2. Press [AUTO SCAN].
Auto scan starts.
Indicates
auto scan
3. Press [AUTO SCAN] when you find the desired station.
Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].
To improve reception
FM: Extend the whip antenna and adjust its direction.
AM: Adjust facing of the unit.
If noise is excessive in the FM stereo mode
Press [FM MODE]. ("
" lights up.)
Sound will be produced in monaural, but this also reduces noise.
Press the button again to cancel. ("
To receive FM broadcasts allocated in 0.1 MHz
(Only from the main unit)
First press [BAND] to select "AM". Now, press and hold [BAND]. The dis-
play changes in a few seconds to show the current lowest FM frequency.
Continue to hold down the button.
The minimum frequency changes and the step is changed at the same
time. Changing the step erases all preset stations.
Repeat the above to change the step back.
Listening to radio broadcasts
5
4
"
" lights when an FM stereo
broadcast is being received.
] to "TUNER".
" goes out.)
Preset tuning
Preset the stations (12 FM and 12 AM) to make tuning simpler.
1
Tune to the desired station.
Do steps 1–4 on the left.
2
Press [MEMORY].
3
While "
" and the frequency are
flashing
Press [MEMORY].
4
While "
" and the preset channel
are flashing
Press [–/g] or [f/+] to
select the desired channel.
(Remote control: [4 4 4 4 4 ] or [3 3 3 3 3 ])
5
Press [MEMORY].
(This completes presetting.)
6
Repeat steps 1–5 to preset other stations.
Note
If "
" goes off during presetting, return to step 2.
To listen to preset channels
1 1 1 1 1
Press [BAND] to select "FM" or "AM".
2
(Omit this step if using the remote control)
Press [TUNE MODE] to display
"
".
3
Press [–/ g] or [f/+] to select
the desired channel (1–12).
(Remote control: [4 4 4 4 4 ] or [3 3 3 3 3 ])
To use preset scan
You can search for a station by listening to all preset channels for 8
1
2
seconds each.
1. Do steps
to
above.
For remote control, replace [–/ g] or [f/+] described below with [4 4 4 4 4 ]
or [3 3 3 3 3 ].
2. Press and hold [–/ g] or [f/+] until "PS" appears on the display.
Indicates
preset scan
3. Press [–/ g] or [f/+] when you find the desired channel.
Preset scan ends after searching through each preset channel once.
To stop during the process, press [–/ g] or [f/+].
3
RQT6742
2 3 5
4
2
3
1
How to preset
Preset channel
Preset channel