3Com 3C16610 - Superstack II Dual Speed HUB 500 사용자 설명서 - 페이지 6
{카테고리_이름} 3Com 3C16610 - Superstack II Dual Speed HUB 500에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. 3Com 3C16610 - Superstack II Dual Speed HUB 500 9 페이지. 12-port tp/24-port tp
페이지 인쇄M
OUNTING
Introduction
The Dual Speed Hub 500 is supplied with two mounting brackets and
four screws. These are used for rack mounting and wall mounting the
unit. When mounting the unit, you should take note of the guidelines
given in " Positioning the Dual Speed Hub 500 " overleaf.
Wall Mounting the Units
CAUTION: Disconnect all cables from the unit(s) before
continuing. Remove the self-adhesive pads from the underside
of the unit(s), if already fitted.
The maximum number of units that you can wall mount
together is two units.
Fitting the brackets to wall mount one unit:
1
Place the unit the right way up on a hard, flat surface with the
front facing towards you.
2
Locate a mounting bracket over the mounting holes on one side
of the unit, as shown in Figure 1 below.
3
Insert the two screws and fully tighten with a screwdriver.
Repeat the last two steps for the other side of the unit.
Fitting the brackets to wall mount two units:
1
Stack the units the right way up on a hard, flat surface with the
front facing towards you.
2
Locate two mounting brackets over the mounting holes on one
side of the units, as shown in Figure 2 below.
3
Insert the three screws and fully tighten with a screwdriver.
Repeat the last two steps for the other side of the units.
Figure 1 Wall Mounting One Unit
T
ECHNICAL
Related Standards
The SuperStack® II Dual Speed Hub 500 has been designed and certified
to the following standards:
Functional
ISO/IEC 8802-3, IEEE 802.3, IEEE 802.3u, IEEE 802.1D
Safety
UL 1950, EN 60950, CSA 22.2 #950, IEC 950
EMC
EN 55022 Class A*, EN 50082-1, FCC Part 15
Subpart B Class A, ICES-003 Class A, VCCI Class A*,
AS/NZS 3548 Class A*
*The use of unscreened cables (Category 3 or 5 for 10BASE-T ports
or Category 5 for 100BASE-TX ports) complies with the Class A
requirements.
Environmental
EN 60068 (IEC 68)
Environmental
Operating Temperature
Humidity
K
I
IT
Figure 2 Wall Mounting Two Units
I
NFORMATION
0–50 ° C (32–122 ° F)
0–95% (non-condensing)
NSTRUCTIONS
To wall mount the unit(s):
Ensure that the wall you are going to use is smooth, flat, dry and sturdy.
Attach a piece of plywood, about 30cm x 50cm x 1.5cm (12in. x 20in. x
0.5in.) in size, securely to the wall if necessary, and mount the unit(s) as
follows:
1
Position the unit(s) against the wall (or plywood) ensuring that
the ventilation holes face sideways. Mark on the wall the position
of the screws holes for both wall brackets. Drill the four holes.
2
Using suitable fixings and screws (not provided), attach the unit(s)
securely to the wall (or plywood).
Reconnect all cables.
Rack Mounting the Units
The Dual Speed Hub 500 is 1U high and will fit a standard 19in. rack.
CAUTION: Disconnect all cables from the unit before
continuing. Remove the self-adhesive pads from the underside
of unit, if already fitted.
1
Place the unit the right way up on a hard, flat surface with the
front facing towards you.
2
Locate a mounting bracket over the mounting holes on one side
of the unit, as shown in Figure 3 below.
3
Insert the two screws and fully tighten with a suitable screwdriver.
4
Repeat the two previous steps for the other side of the unit.
5
Insert the unit into the 19in. rack and secure with suitable screws
(not provided).
Reconnect all cables.
Physical
Width
Depth
Height
Weight
Mounting
Electrical
Power Inlet
AC Line Frequency
Power Consumption
Power Dissipation
Input Voltage
Current Rating
6
Figure 3 Rack Mounting
440mm (17.3in.)
230mm (9in.)
44mm (1.7in.) or 1U
3C16610: 2.55kg (5.6lb) / 3C16611: 2.66kg (5.8lb)
free standing, or 19in. rack or wall mounted using
the mounting kit supplied
IEC 320
50/60 Hz
3C16610: 36 VA / 3C16611: 40 VA
3C16610: 123 BTU/hr
3C16611: 137 BTU/hr
100–240 VAC
1.0 Amps (maximum)