Bionaire BCH3620 지침 리플렛

{카테고리_이름} Bionaire BCH3620에 대한 지침 리플렛을 온라인으로 검색하거나 PDF를 다운로드하세요. Bionaire BCH3620 2 페이지. Digital tower ceramic heater with remote control
Bionaire BCH3620에 대해서도 마찬가지입니다: 소유자 매뉴얼 (6 페이지)

페이지 인쇄

BCH3620-CN_08EFM1.qxd:OEM

5/28/08

8:41 AM

Page 1

HEATER SAFETY

PLEASE READ AND SAVE

digital TOWER

THESE IMPORTANT

CERAMIC

SAFEGUARDS

IMPORTANT INSTRUCTIONS

heater with remote control

When using electrical appliances, basic safety precautions

should always be followed to reduce the risk of fire, electric

BCH3620

shock, and injury to persons, including the following:

1. Read all instructions before using the appliance.

2. To avoid fire or shock hazard, plug the appliance

directly into a 120V AC electrical outlet.

3. The heater is hot when in use. To avoid burns, DO NOT

let bare skin touch hot surfaces. If provided, use handles

when moving this heater. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes, and

curtains at least 3 ft (0.9 m) from the front of the heater

and keep them away from the sides and rear.

4. DO NOT run cord under carpeting. DO NOT cover cord

with throw rugs, runners, or the like. Arrange cord

away from traffic area and where it will not be tripped

over.

5. This heater is not intended for use in bathrooms, laundry

areas and similar indoor locations. NEVER locate

heater where it may fall into a bathtub or other water

container.

6. Extreme caution is necessary when any heater is used

by, or near children or invalids, and whenever the

heater is left operating and unattended.

7. Always unplug the heater when not in use.

8. When unplugging, be sure to pull by the plug and not

the cord.

9. DO NOT insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause an

electric shock or fire, or damage the heater.

10.DO NOT operate heater with a damaged cord or plug,

or after the heater malfunctions, or has been damaged

Read instructions before operating.

in any manner. Return appliance to manufacturer for

Retain for future reference.

examination, electrical or mechanical adjustment, or repair.

Instruction Leaflet

11.A heater has hot and arcing or sparking parts inside.

DO NOT use it in areas where gasoline, paint, or

☎

flammable liquids are used or stored.

INFO-LINE

12.Use appliance only for intended household use as

If after having read this leaflet, you have any

described in this manual. Any other use not

questions or comments on your heater,

recommended by the manufacturer may cause fire,

call 1-800-253-2764 in North America.

electric shock, or injury to persons. The use of

129340

attachments not recommended or sold by the

manufacturer may cause hazards.

CLEANING/MAINTENANCE

1. Always unplug the heater before cleaning.

2. Clean the unit with a soft cloth moistened with a mild

1. Every few weeks, check the condition of the Filter on

soap solution.

the rear side of the heater.

3. NEVER use abrasive or flammable solvents to clean the

2. Remove the Filter Cover, and take the Filter out to flush

unit.

gently with tap water from the inside face (Clean side) to

remove the dirt and dust (See Fig. 3 & 4).

4. After cleaning, be sure to completely dry the unit with a

cloth or towel.

3. Drain excess water drip dry.

4. Resintall the Filter once it is dry, put back the Filter

After Season Care:

Cover in place.

1. Store heater in a cool, dry location.

2. The manufacturer recommends that you store the unit

in its original carton.

☛

TIP: Over time, dust may accumulate on the front grills.

This can be removed by wiping the unit with a damp

cloth. Always unplug unit and allow to cool prior to

Filter

cleaning.

Filter

Cover

TROUBLESHOOTING

• UNPLUG THE UNIT.

• Make sure the electrical outlet or circuit breaker is

working.

• Check for obstructions. If you find an obstruction turn

the heater OFF, and unplug the unit. Carefully remove

the obstruction and follow the reset instructions.

• The temperature may be set too low. Adjust the

thermostat until the heater restarts.

If you have any questions regarding your product or

would like to learn more about other Bionaire

Pour water in this direction (Clean side)

please contact our Consumer Service Department at

1-800-253-2764 or visit our website at www.bionaire.com.

Dirty side

13.DO NOT use outdoors.

14.To prevent a possible fire, DO NOT block air intakes or

exhaust in any manner. DO NOT use on soft surfaces,

like a bed, where openings may become blocked.

15.To disconnect heater, turn controls to OFF, then remove

plug from outlet.

16.Avoid the use of an extension cord because the

extension cord may overheat and cause a risk of fire.

However, if you have to use an extension cord, the

cord shall be No. 14 AWG minimum size and rated not

less than 1875 watts.

17.If the heater will not operate, see specific instructions

on Auto Safety Shut-off.

18.DO NOT attempt to repair or adjust any electrical or

mechanical functions on this unit. Doing so will void

your warranty. The inside of the unit contains no user

serviceable parts. All servicing should be performed by

qualified personnel only.

19.DISCONTINUE USE IF PLUG OR OUTLET IS HOT.

RECOMMEND OUTLET BE REPLACED IF PLUG OR

OUTLET IS HOT TO TOUCH.

PLEASE SAVE THESE

INSTRUCTIONS

CONSUMER SAFETY INFORMATION

This appliance has a POLARIZED AC

PLUG (one blade is wider than the other).

To reduce the risk of electric shock, this

plug is intended to fit in a polarized outlet

only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician

to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR

DEFEAT THIS SAFETY FEATURE IN ANY WAY.

PLEASE READ AND SAVE

THESE IMPORTANT

SAFETY INSTRUCTIONS

TECHNICAL SPECIFICATIONS

• Amps: 12.5

• Wattage: 1500W (+5% -15%)

• Working Voltage: 120V AC/60 Hz

AUTO SAFETY SHUT-OFF INSTANT TIP OVER

PROTECTION

Sunbeam Products, Inc. doing business as Jarden

Consumer Solutions or if in Canada, Sunbeam Corporation

(Canada) Limited doing business as Jarden Consumer

Solutions (collectively "JCS") warrants that for a period of

five years from the date of purchase, this product will be

free from defects in material and workmanship. JCS, at its

option, will repair or replace this product or any component

of the product found to be defective during the warranty

period. Replacement will be made with a new or

remanufactured product or component. If the product is no

longer available, replacement may be made with a similar

product of equal or greater value. This is your exclusive

warranty. Do NOT attempt to repair or adjust any electrical

or mechanical functions on this product. Doing so will void

this warranty.

This warranty is valid for the original retail purchaser from the

date of initial retail purchase and is not transferable. Keep the

original sales receipt. Proof of purchase is required to obtain

warranty performance. JCS dealers, service centers, or retail

stores selling JCS products do not have the right to alter,

modify or any way change the terms and conditions of this

warranty.

This warranty does not cover normal wear of parts or

damage resulting from any of the following: negligent use or

misuse of the product, use on improper voltage or current,

use contrary to the operating instructions, disassembly, repair

or alteration by anyone other than JCS or an authorized JCS

service center. Further, the warranty does not cover: Acts of

God, such as fire, flood, hurricanes and tornadoes.

JCS shall not be liable for any incidental or consequential

damages caused by the breach of any express, implied or

statutory warranty or condition.

Except to the extent prohibited by applicable law, any

implied warranty or condition of merchantability or fitness

products,

for a particular purpose is limited in duration to the duration

of the above warranty.

JCS disclaims all other warranties, conditions or

representations, express, implied, statutory or otherwise.

JCS shall not be liable for any damages of any kind

resulting from the purchase, use or misuse of, or inability to

use the product including incidental, special, consequential

or similar damages or loss of profits, or for any breach of

contract, fundamental or otherwise, or for any claim

brought against purchaser by any other party.

Some provinces, states or jurisdictions do not allow the

exclusion or limitation of incidental or consequential

damages or limitations on how long an implied warranty

lasts, so the above limitations or exclusion may not apply

to you.

This heater is equipped with a patented, technologically

4. Once you have reached your desired temperature, the

advanced safety system that requires the user to reset the

display will return to current room temperature and

gradually increase until the room has reached the

heater if there is a potential overheat situation. When a

preset temperature.

potential overheat temperature is reached, the system will

automatically shut the heater off. It can only resume

5. If the unit will not start in the digital thermostat mode,

please make sure the "set temperature" is higher than

operation when the user resets the unit.

the current room temperature.

NOTE: It is normal for the heater to cycle ON and OFF as

1. Unplug the heater and wait 10 minutes for the unit to

it maintains the preset temperature. To prevent the unit

cool down.

from cycling, you need to raise the thermostat setting.

2. After the 10 minutes, plug the unit in again and operate

When the preset temperature is reached, the fan will run

normally.

for 30 seconds without heat. This cool down process

ensures an accurate and consistent temperature reading. If

you unplug the heater, you will have to reset the digital

When the unit is accidentally knocked over, it will instantly

thermostat again by following the above instructions.

shut off. To reset, simply place the heater in an upright

position. Press the MODE button and it will operate normally.

NOTE: To shut the unit off at any time, press and hold the

MODE button down for two seconds.

PRE-OPERATING INSTRUCTIONS

NOTE: Digital thermostat has memory. The digital

1. Carefully remove your heater from the box. Please save

thermostat will remember the previous temperature setting

the carton for off-season storage.

after the unit has been turned off. However, if the unit is

2. Make sure the unit is in the OFF position before

unplugged, the digital thermostat will be reset and will no

plugging the heater into the outlet.

longer remember the previous temperature setting.

3. Place heater on a firm level surface.

USING THE PROGRAMMABLE TIMER

4. Avoid overloading your circuit by not using other high

wattage appliances in the same outlet. At 1500 Watts,

Digital thermostat allows the user to program the heater to

this unit draws 12.5 Amps.

turn on at a preset time, or turn off after a set amount of time.

NOTE: The power light will illuminate when the heater is

turned on.

1. Select the Mode and/or temperature you wish the

DIGITAL THERMOSTAT

heater to run in.

2. While the heater is running, press and hold the up and

Your heater is equipped with a Digital Thermostat that

down buttons simultaneously.

allows you to set your heater to your precise comfort level.

3. By pressing the up and down buttons, program the

SETTING THE DIGITAL THERMOSTAT:

heater to turn off in up to 16 hours from the current

time, in increments of 1 hour.

4. After setting the timer, the LED display will return to

MODE BUTTON

TEMP/TIMER UP

show the current room temperature. A LED will

BUTTON

illuminate to show that the timer is activated.

5. After the predetermined length of time has passed, the

heater will automatically shut off.

OSCILLATION

TEMP/TIMER

BUTTON

DOWN BUTTON

1. While the heater is off, press and hold the up and down

1. Press the Mode Button once for manual HI power. The

buttons simultaneously.

heater will run continuously on HI.

2. By pressing the up and down buttons, program the

2. Press the Mode Button again for manual LO power.

heater to turn on up to 16 hours in advance of current

The heater will run continuously on LO.

time, in increments of 1 hour.

3. Press the Mode Button for a third time for Auto Mode

3. After the preset length of time has passed, the heater

HI Power (AH) or press again for Auto Mode LO Power

will automatically turn on Auto Mode HI Power at 75˚F

(AL). In either of these modes you may then press the

(24˚C) for a preset time of 2 hours.

up, and down buttons to reach your desired

temperature.

This warranty gives you specific legal rights, and you may

also have other rights that vary from province to province,

state to state or jurisdiction to jurisdiction.

In the U.S.A.

If you have any question regarding this warranty or would

like to obtain warranty service, please call 1-800-253-2764

and a convenient service center address will be provided

to you.

In Canada

If you have any question regarding this warranty or would

like to obtain warranty service, please call 1-800-253-2764

and a convenient service center address will be provided

to you.

In the U.S.A., this warranty is offered by Sunbeam

Products, Inc. doing business Jarden Consumer Solutions

located in Boca Raton, Florida 33431. In Canada, this

warranty is offered by Sunbeam Corporation (Canada)

Limited doing business as Jarden Consumer Solutions,

located at 20 B Hereford Street, Brampton, Ontario L6Y

0M1. If you have any other problem or claim in connection

with this product, please write our Consumer Service

Department.

Distributed by Sunbeam Products, Inc. doing business as

Jarden Consumer Solutions, Boca Raton, Florida 33431.

BCH3620CN08EFM1

Printed in China

OSCILLATION INSTRUCTIONS

1. Select the desired temperature and mode settings and

press the oscillation button to the ON position.

2. To stop oscillation, press the oscillation button again.

3. Please do not manually turn the heater on the base; it

is designed to turn only by motorized oscillation.

REMOTE CONTROL INSTRUCTIONS

1. Before operation, insert 2 "AAA" batteries into the back

of the remote control.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (nickel-cadmium) batteries.

The remote control for this unit has the capability of

operating all control panel functions. Please note this

remote control will not work through walls.

POWER: To turn the unit on press the Mode/On Button.

To turn the unit off press the OFF button.

MODES: To scroll through the various modes LO, HI, AL

and AH press the Mode Button until you reach your

desired setting.

OSCILLATION: To start oscillation, press the Osc. Button

once. To stop oscillation press the button again.

TEMPERATURE: To increase the temperature setting,

press the Temp Up button. To decrease the temperature

setting that you desire press the Temp Down button.

TIMER: To activate the timer

from the remote control, press

the button marked Timer. From

there you can press the Temp

Up or Temp Down button, which

will give you the ability to

program the heater to turn on or

off in 1 hour increments, up to

16 hours. For more information

see the programmable timer

instructions above.