BIONIME Rightest GM100 사용 지침

{카테고리_이름} BIONIME Rightest GM100에 대한 사용 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. BIONIME Rightest GM100 2 페이지. Blood glucose monitoring system
BIONIME Rightest GM100에 대해서도 마찬가지입니다: 사용 지침 (2 페이지)

페이지 인쇄

Blood Glucose Monitoring System

Instructions for Use

Preface

Thank you for selecting the

Blood Glucose Monitoring System.

Please read this manual thoroughly before you start testing. It provides all the

information you need to use the product. You will get a correct test result by the

following instruction of this manual. Please only purchase the test strips in

your country, the use of the test strips of different countries is not

suggested and might get deviated test results under such circumstance.

It is quite important for you to monitor blood glucose regularly. A derived

complication can thus be effectively reduced. Through the assistance of

Blood Glucose Monitoring system, which provides considerate

design and accurate results, your diabetes management can become more

reliable and ease-to-use.

The

Blood Glucose Monitoring System was manufactured by

supported by Bionime Corporation and its authorized representative. If you

have any questions or concerns, please contact your Bionime authorized

representative or call us by phone number, 886 4 24951268 ( GMT+08:00,

08:30~17:30 ). We will provide best assistance and solutions for you.

Intended Use

The

Blood Glucose Monitoring System is intended for in vitro

diagnostic use ( for self-testing ) only ( outside the body ) and coding is not

required. The testing result is calibrated to be plasma equivalent for test with

fresh capillary whole blood samples from the fingertip, palm or forearm

depends on what kind of lancing device you are using. You may consult your

healthcare professional for instructions on how to use the system correctly. Our

customer support staff is available to assist you as well.

Package of Meter Kit

Meter

7. Disposable Sterile Lancets

(10pcs) *

Test Strips (0/10/25 pcs) *

8. Instruction for the lancing device *

Control Solutions *

9. Log Book

Instructions for Use

10. Warranty Card + Emergency

Blood Glucose Test Strip

11. CR2032 Battery (Inserted into the

Package Insert *

meter)

Lancing Device *

12. Carrying Case *

( Different packages have different bundled items. Some of packages might not

include ＊ items.)

2 ＊

3 ＊

Test Strips

5 ＊

7 ＊

8 ＊

6 ＊

The

Meter

Test Strip Port

Insert test strip here until you

hear a click.

Display Window

Show your test result,

messages and relative

Model Number

information.

Meter Serial

Number

Main Button

Press to turn on/off meter.

Battery Cover

Switch different function

Slide cover to

screen.

change battery.

Press and hold down until

enter to the setting mode.

Plastic Tape

(There will be a power-off

Pull it off to activate meter.

period during this process.)

Precautions

- Before using the

System to test your blood glucose, please read

all the instructions and practice the tests including quality control test.

- Please do the quality control test regularly to make sure the test results are

accurate .

- The

GM100 Blood Glucose Meter can only be used with the

GS100 Blood Glucose Test strips. The use of any other brand

strips should not be used under any circumstances. The use of other brands

of strips may produce inaccurate results.

- The

Blood Glucose Monitoring System is intended for self-testing. It

should not be used to diagnose diabetes mellitus.

Blood Glucose Monitoring System has not been validated for use

on neonates. Therefore, it's not intended for use of neonates.

- This meter can be only tested with capillary whole blood. Please don't test with

arterial blood.

- Do the test at least 30 minutes after moving into a different location with

significant change in temperature.

- Dispose of used batteries properly.

- Please note the meter kit contains small parts like test strips which could result

in a choking hazard for children.

- Prevent water from entering the meter. Never immerse the meter or hold it

under running water.

- The minimum blood sample size for testing is 1.4µl :(

)

1.0

µl

1.4

µl

2.0

µl

3.0

µl

Sample Size Example

We suggest you use a sample between 1.4~2.5µl. A blood sample size above

4.0µl is too large. A blood sample size below 1.4µl may give an inaccurate test

result. In this case, repeat the test with a new test strip.

The

Test Strip ( GS100 Test Strip )

GM100 is designed to use with GS100 strip only. Please note that

misuse of other strips might cause unexpected damage or produce

inaccurate test results.

Sample Entry

Noble Metal Electrodes

Apply a drop of blood or control solution

Electrochemical sensor

here. The test request is only 1.4 of blood.

Hand Bar

Grip here to insert

test strip into meter.

Indication Symbol

View Window

Insert strip with indication symbol

This window is yellow before applying

up and toward meter.

blood sample. It gradually turns red

when filled with blood.

Electrode Contacts

Sensing signal output terminals.

PRECAUTION

- Re-cap the test strip the vial immediately after removing a test strip.

- Do not reuse test strips.

- Do not use expired test strips.

- Record the date of opening a new strip vial for the first time. Discard the

vial of strips after 3 month from opening.

- Store the test strips in a cool and dry location. Do not expose to direct

sunlight or heat.

- For detailed information, please refer to the

GS100 Test Strip

Package Insert.

Battery Installation

Your meter comes with one CR2032, 3volt, battery installed. One

new battery will provide power to perform about 1000 tests under

normal use. Before using it, please pull off the plastic tape and

press the main button to activate the meter. The low battery

symbol "

" will keep appearing on your display if your battery

runs low. Please keep spares on hand and replace the battery

soon when a battery symbol appears.

1. Turn the meter over. Press and push battery

cover to open.

2. Install the battery. Be sure to put battery in

correct direction.

3. Slide the battery cover back until it snaps into place.

4. The meter performs a self-test and all symbols on the display

will blink.

5. Press any button to exit the self-test and enter Setting Mode.

6. Set the time and date when the batteries are replaced. See Setting the Date,

Time and Unit section. Prior test results are still stored in the memory.

PRECAUTION

- Danger of explosion might happen if the battery is incorrectly replaced.

- Please follow the local regulation and discard a used battery properly.

Setting Up Your Meter-Setting the Date, Time, and Unit ......

You can enter Setting Mode by below two ways.

1. Reload battery

After removing the battery, please press the main button for several times

until no signal on screen, then follow the battery installation steps to load

battery. The meter will do self test. Press the main button to close the test

and enter Setting Mode.

2. With Battery inserted

Press the main button first to turn on the meter. Then press and hold the main

button for 5 seconds (the meter will be turned off during this period, please

keep pressing) until you hear a beep, indicating you have successfully

entered Setting Mode. The display screen will show setting data.

NOTE

- When you keep pressing the main button for 2 seconds, the display on

screen will turn off. Please don't care it. Keep pressing the main button

till entering setting data.

- Quick press the main button allows you to change setting while hold it

4 µl

for 2 seconds will confirm the setting. However, if you press and hold

the main button over 5 seconds it will escape from setting mode and

return to time screen.

1. Year setting

With the year format blinking, press the main button to adjust

it. Then hold the same button for 2 seconds to confirm it.

Meantime, it will shift to next digit for setting. Repeat the above

action until the year setting is completed. Then it will move to

month setting.

2. Month setting

With the month blinking, press the main button until the

current month appears. Then hold the same button for 2

seconds to confirm it and move to day setting.

µl

3. Day setting

With the day blinking, press the main button to adjust it. Then

hold the same button for 2 seconds to confirm it. Meantime, it

will shift to next digit for setting. Repeat the above action until

the day setting is completed. Then it will move to time format

setting.

4. Time format 12/24H selection

With the time format blinking, press the main

button to adjust it. Then hold the same button

for 2 seconds to confirm it and move to hours

setting.

5. Hour setting

With the hour blinking, press the main button until the current

hour appears. Then hold the same button for 2 seconds to

confirm it and move to minute setting.

6. Minute setting

With the minute blinking, press the main button

to adjust it. Then hold the same button for 2

seconds to confirm it. Meantime, it will shift to

next digit for setting. Repeat the above action

until the minute setting is completed. Then it will

move to average-day setting.

7. Average-day setting

With the number " 1, 7, 14, 30 " blinking, press

the main button for the days of the average you

would like to read. Then hold the same button

for 2 seconds to confirm it and move to

measurement unit setting.

8. Setting the unit of measurement

With milligrams per deciliter (mg/dL) or

minimole per liter (mmol/L) blinking, press the

main button to switch. Then hold the same button for 2 seconds to confirm it.

9. Ending setting

After confirm the measurement unit, you'll hear a sound of " beep ". All the

settings are saved and completed and will return to time screen.

NOTE

- When you do not do any settings of meter for over 2 minutes, the meter

will leave setting mode and power off automatically.

- Any time you would like to escape from the setting mode, please press

and hold the main button for over 5 seconds. Meantime, all the current

settings will be saved.

Turning on /off the Meter

1. Auto Power off

The meter will power off automatically if you don't operate it over 2 minutes.

2. Manual Power off

If you want to turn off the meter, please keep pressing the main button for 2

seconds.

3. How to turn on the Power

1) Press the main button

2) Insert one piece of test strip

Performing a Blood Test

Depth adjustable cap

Release button

Plunger

Lancet carrier

Hub

1. Pull off the depth adjustable cap.

2. Insert a new disposable lancet firmly into lancet carrier.

3. Twist off and set aside the protective cover of the disposable lancet.

4. Replace the depth adjustable cap.

5. Choose a depth of penetration by rotating the

top portion of the depth adjustable cap until

the setting depth matches the window.

Settings are based on skin type "

" for soft

or thin skin; "

" for average skin; "

" for

thick or calloused skin.

6. Hold the hub in one hand and pull on the plunger in the other hand. The

device will be cocked. Release the plunger, it will automatically move back to

its original position near the hub.

7. Wash your hands with warm

soapy water and dry thoroughly.

8. Take one strip from the vial. Re-

cap the vial cap immediately.

9. Insert the strip into the strip port on meter with the indication symbol facing

up.

10. While the blood drop symbol flashing, you are ready to apply the blood

sample.

11. Place the lancing device against the pad of

your fingertip and press the release button.

The best puncture sites are on the middle or

ring fingers. Press the release button.

12. Touch and hold the drop to the edge of

sample entry until you hear a " beep " and the

view window is totally filled with blood. If the

view window is not totally filled with blood or

the test does not start. Please discard the test

strip and repeat the test with a new test strip.

13. You will see the countdown mode on the

screen. After 8 seconds, the test result

appears.

14. Pull off the depth adjustable cap. Without touching the used disposable

lancet, stick the lancet tip into the protective cover.

15. Hold the release button in one hand and pull on the plunger in the other

hand will safely eject the used disposable lancet.

16. Discard the used disposable lancet into an appropriate puncture-proof or

biohazard container.

17. Replace the depth adjustable cap after finishing the test.

PRECAUTION

Do not touch your blood drop to the sample entry on the strip until you

see the "

" appear. The meter is performing an internal test and will

display "

" and "

" if you apply blood too soon. Then you will waste

a test strip.