Dickson KT6 사용자 설명서 - 페이지 2

{카테고리_이름} Dickson KT6에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dickson KT6 4 페이지. 6” temperature chart recorder
Dickson KT6에 대해서도 마찬가지입니다: 매뉴얼 (11 페이지)

페이지 인쇄

GETTING STARTED

IMPORTANT

7-DAY CHART ROTATION

Dickson Chart Recorder accuracy specifications are only valid with the use of authentic

Dickson brand charts and pens. The specifications for chart printing, die cutting and paper

0 TO 100°F

absorption rates, and the complementary bleed rate specifications of pens are critical factors

in determining system accuracy.

QUICK START

TO BEGIN OPERATION

1. Remove the protective pen cap.

2. Connect probe. Make sure the KTC probe is

connected firmly to the Replaceable Sensor™ and

that the Replaceable Sensor™ is plugged in firmly to

the chart recorder.

3. Insert 4AA batteries and plug in AC adapter (Reference

Guide on back). Unit will power on.

4. The instrument will move pen to the appropriate

readings.

5. Install the chart that matches the DIP SWITCH settings

(Reference settings label on the battery door to set the

correct dip switch positions for the chart)

POWER

The KT6 operates on AC power with an optional 4AA battery backup. Depending on

chart rotation selected and model; battery backup will last approximately 3 days.

Note: ALARM and RELAYS will not operate under battery only power.

LED Indicators

• Solid Green — AC Power with Battery Backup

• Solid Red — AC Power with Low Battery or No Battery

• Blinks Green — Battery Only

• Blinks Red — Battery Only (Low Battery)

KEYPAD AND BUTTON FUNCTIONS

ON/OFF

The ON/OFF key turns the unit on and off.

PEN HOME

If the pen is located on the outside edge of the chart,

press PEN HOME to move pen to recording position. If

the pen is located on the chart, press PEN HOME to move

the pen to the outside edge of the chart.

ALARM (KT6P5)

• To set the ALARM, make sure unit is on and press and

hold the ALARM button. The LED will blink red rapidly

for about five seconds, then the LED will turn solid

green. Release the ALARM button and the LED will

turn solid red. At this point the display will show "On"

or "Off". Pressing either the ADJUST-UP or ADJUST-

6. Press the PEN HOME key to move the pen to the

outside of the chart. The pen is automatically raised

off the chart.

7. Remove the old chart, place the new chart on the

CHART HUB being certain that the edge of the chart

slides under the Chart Guide Clip located at the

outside of the chart.

8. Set the appropriate time. Set the chart time manually

by inserting a coin into the groove in the CHART HUB

and turning clockwise until the correct hour (and day

if applicable) on the chart is referenced to the timing

arrow (just to the right of the pen tip on the dial). Press

PEN HOME to move the pen back onto the chart.

POWER

LED

PEN

HOME

ON/OFF

ALARM

(Alarm button on KT6P5 only)

DOWN buttons, located on the back of the unit next

to the DIP SWITCH, will toggle the ALARM on or off.

• Pressing PEN HOME will scroll to the next ALARM

option. The options are as follows:

» ALARM on or off

» Pen 1 ALARM minimum

» Pen 1 ALARM maximum

• In order to set pen ALARM minimum and maximum,

pressing ADJUST-UP will increase the ALARM value,

and pressing ADJUST-DOWN will decrease the ALARM

value. There is acceleration if the ADJUST-UP button

is held down.

• Repetitively pressing the PEN HOME button will scroll

through the three options until the ALARM button

is pressed to exit from ALARM adjust. Each press of

the PEN HOME or ALARM buttons will store the new

settings. The unit will take one minute to exit ALARM

Set Mode once the ALARM button is pressed.

• If the ALARM is triggered, the LED will show as solid

red and the ALARM will sound. Press the ALARM

button to silence the audible ALARM.

ALARM RELAYS (KT6P5)

The SPST 24V 500mA RELAY contacts are normally open

and will close on ALARM conditions when the ALARMS

are enabled. RELAY contacts are always functional when

DIP SWITCH SETUP

To setup the KT6 recorder for your specific

application, you might need to change some of the

DIP SWITCHES. The DIP SWITCHES are located on the

back of the unit. Use a pen or small screw driver to

flip the switches.

Remember to install the correct chart to match the

corresponding DIP SWITCH setting.

RECORDING TIME

7 Day

#2 DOWN

24 Hour

#2 UP

RECORD IN °F OR °C

°F

#3 DOWN

°C

#3 UP

TEMPERATURE RANGE

Select the temperature range that matches the chart paper

0° to +100° F/C

#4 DOWN — #5 DOWN — #6 DOWN

-50° TO 0° F/C

#4 DOWN — #5 DOWN — #6 UP

-100° TO 0° F/C

#4 DOWN — #5 UP — #6 UP

-50° TO 50° F/C

#4 UP — #5 DOWN — #6 DOWN

0° to 50° F/C

#4 DOWN — #5 UP — #6 DOWN

50° to 100° F/C

#4 UP — #5 UP — #6 UP

0° to 500° F

#4 UP — #5 UP — #6 DOWN

0° to 250° F/C

#4 UP — #5 DOWN — #6 UP

the ALARM is enabled. The RELAY will close only during

minimum and maximum ALARM conditions. RELAYS will

not operate under battery only power conditions.

CH1 = PINS 1,2,3

• Pins 1 and 2 make contact

when CH1 is in alarm

• Pins 1 and 3 make contact

when CH1 is not in alarm

Slide toggle UP for ON position

Slide toggle DOWN for OFF position

Dip Switches 7 and 8 are not active on this recorder