EPC EPC9113 빠른 시작 매뉴얼 - 페이지 5

{카테고리_이름} EPC EPC9113에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. EPC EPC9113 16 페이지.

페이지 인쇄

QUICK START GUIDE

QUICK START PROCEDURE

The EPC9113 demonstration system is easy to set up and evaluate the

performance of the eGaN FET in a wireless power transfer application. Refer

to Figure 1 to assemble the system and Figures 6 and 8 for proper connection

and measurement setup before following the testing procedures.

The EPC9509 can be operated using any one of two alternative methods:

a. Using the pre-regulator

b. Bypassing the pre-regulator

a. Operation using the pre-regulator

The pre-regulator is used to supply power to the amplifier in this mode

and will limit the coil current, power delivered or maximum supply volt-

age to the amplifier based on the pre-determined settings.

The main 19 V supply must be capable of delivering 2 ADC. DO NOT turn

up the voltage of this supply when instructed to power up the board,

instead simply turn on the supply. The EPC9509 board includes a pre-

regulator to ensure proper operation of the board including start up.

1. Make sure the entire system is fully assembled prior to making electrical

connections and make sure jumper JP1 is installed. Also make sure the

source coil and device coil with load are connected.

2. With power off, connect the main input power supply bus to J1 as

shown in Figure 3. Note the polarity of the supply connector.

3. Make sure all instrumentation is connected to the system.

4. Turn on the main supply voltage to the required value (19 V)

5. Once operation has been confirmed, observe the output voltage

and other parameters on both the amplifier and device boards.

6. For shutdown, please follow steps in the reverse order.

b. Operation bypassing the pre-regulator

In this mode, the pre-regulator is bypassed and the main power is

connected directly to the amplifier. This allows the amplifier to be

operated using an external regulator.

In this mode there is no protection for ensuring the correct operating

conditions for the eGaN FETs.

1. Make sure the entire system is fully assembled prior to making

electrical connections and make sure jumper JP1 has been removed

and installed in JP50 to disable the pre-regulator and to place the

EPC9509 amplifier in bypass mode. Also make sure the source coil and

device coil with load are connected.

2. With power off, connect the main input power supply bus +V

bottom pin of JP1 and the ground to the ground connection of J1 as

shown in Figure 3.

3. With power off, connect the control input power supply bus to J1.

Note the polarity of the supply connector. This is used to power the

gate drivers and logic circuits.

4. Make sure all instrumentation is connected to the system.

5. Turn on the control supply – make sure the supply is 19 V range.

6. Turn on the main supply voltage to the required value (it is

recommended to start at 0 V and do not exceed the absolute

maximum voltage of 52 V).

EPC – EFFICIENT POWER CONVERSION CORPORATION |

7. Once operation has been confirmed, adjust the main supply

voltage within the operating range and observe the output voltage,

efficiency and other parameters on both the amplifier and device boards.

8. For shutdown, please follow steps in the reverse order. Start by

reducing the main supply voltage to 0 V followed by steps 6 through 2.

NOTE.

1. When measuring the high frequency content switch-node (Source Coil Voltage), care

must be taken to avoid long ground leads. An oscilloscope probe connection (preferred

method) has been built into the board to simplify the measurement of the Source Coil

voltage (shown in Figure 4).

2. To maintain control stability, the red LED for voltage mode indicator on the EPC9509

version 1.0 has been disabled. This will be corrected in subsequent revisions of the

board. For questions regarding this LED function, please contact EPC.

3. You may experience audible noise emanating from the inductor of the SEPIC converter.

This is due to a minor instability. This minor instability does not impact the performance

of the power amplifier or the protection circuitry of the system.

4. AVOID using a Lab Benchtop programmable DC as the load for the category 3 device

board. These loads have low control bandwidth and will cause the EPC9113 system to

oscillate at a low frequency and may lead to failure. It is recommended to use a fixed low

inductance resistor as an initial load. Once a design matures, a post regulator, such as a

Buck converter, can be used.

THERMAL CONSIDERATIONS

The EPC9113 demonstration system showcases the EPC2108 and

EPC2036 in a wireless energy transfer application. Although the

electrical performance surpasses that of traditional silicon devices,

their relatively smaller size does magnify the thermal management

requirements. The operator must observe the temperature of the gate

driver and eGaN FETs to ensure that both are operating within the

thermal limits as per the datasheets.

NOTE. The EPC9113 demonstration system has limited current and thermal protection

only when operating off the Pre-Regulator. When bypassing the pre-regulator there is no

current or thermal protection on board and care must be exercised not to over-current or

over-temperature the devices. Excessively wide coil coupling and load range variations can

lead to increased losses in the devices.

Pre-Cautions

The EPC9113 demonstration system has no enhanced protection

systems and therefore should be operated with caution. Some specific

precautions are:

1. Never operate the EPC9113 system with a device board that is A4WP

compliant as this system does not communicate with the device to

correctly setup the required operating conditions and doing so can

lead to the failure of the device board. Please contact EPC should

to the

operating the system with an A4WP compliant device is required to

obtain instructions on how to do this. Please contact EPC at info@epc-

co.com should the tuning of the coil be required to change to suite

specific conditions so that it can be correctly adjusted for use with the

ZVS class-D amplifier.

2. There is no heat-sink on the devices and during experimental

evaluation it is possible present conditions to the amplifier that may

cause the devices to overheat. Always check operating conditions and

monitor the temperature of the EPC devices using an IR camera.

3. Never connect the EPC9509 amplifier board into your VNA in an

attempt to measure the output impedance of the amplifier. Doing so

will severely damage the VNA

WWW.EPC-CO.COM

Demonstration System EPC9113

| 5