dicodes Dani Box V2 매뉴얼 - 페이지 5
{카테고리_이름} dicodes Dani Box V2에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. dicodes Dani Box V2 18 페이지.
페이지 인쇄
05 Main Menu (Page 1)
Switching On/Off, Key Locking and Menu-Operation
The dicodes boxmods have three buttons: The bigger vape/fire button positioned
directly below the atomizer and a plus- and minus button below the fire button.
The mod is switched on by shortly pressing any button 5 times. The display shows
"Hello" and the user is led to the main menu. For actively switching off the mod
the fire button is to be pressed shortly 5 times and the display shows "Bye.."
Important Note: The dicodes boxmods differentiate between active switch off and the
automatic switch off after the switch-off-time. When the mod was switched off
driven by the automatic timer, the menu is entered by clicking MonClk (Menu On
Clicks) times the plus or minus button or by pressing the vape-button longer for
immediate vaping. I.e. the user can vape immediately, even when the mod was
completely powered down.
To avoid an unintended change of settings, for example during transportation in a
pocket, the buttons can be locked by pressing the plus- and minus button
simulteanously: "KeyLock" is displayed. To unlock the buttons, agagin both buttons
need to be pressed at the same time, indicated by "UnLock" shown on the display.
By means of the plus and minus buttons it is possible to navigate through the menu, as well as to increase
and decrease values of a parameter after a short waiting until the value is displayed inverted (black on white).
The waiting time from navigation mode to the entry mode is adjustable by means of the parameter "Speed"
in the extended functions menu.
Beside waiting, it is also possible to get from navigation to value entry mode (and back) by
the fire button, i.e. skipping the waiting time. Thus a quick change of adjustments is possible.
In the extended functions menu, the short pressing of the fire button also enables the fast stepping
between the selection of one of the three different sub menues, again skipping the waiting time until the
desired menu is displayed. At this point the fire button also acts as an escape option from the extended
funtions menu, by holding the button for a longer time and releasing it. Note that during the extended
functions menu display vaping is disabled.
Changing the Power Setting
In the Power menu the power setting can be changed by means of the plus/minus
buttons in steps up to the Power-Limit (PLim) value or down to 5W repectively.
If the wrap-around is activated, the setting rolls over at the PLim/5W border.
When wrap-around is disabled, further increase or decrease is blocked at the borders.
The Power-Limit value is adjusted in the Extended Functions Sub-Menu "Heater" and provides a protection
feature for atomizers which are not prepared for high wattage or to reduce the power range intentionally.
The wattage step size is 0.5 Watt below 30W and 1W above.
In the operation mode "Bypass" (mechanical mod), changing the power setting is not available, because the
power is defined by the battery voltage and coil resistance. The menu "Power" is not displayed in this case,
but the value display during and after the vape shows the actual power output to the coil.
With temperature controlled vaping activated, the power setting is the power limit for the temperature
regulator. If the power level is smaller than the value needed to achieve the selected temperature, the
operation changes from a temperature regulator to a temperature limiter. If the power level is sufficiently
high, it sets the heating up speed of the coil until the set-point temperature is reached.
When the battery voltage decreases, power is reduced starting from the voltage set by the parameter
Ubat,min (EF-mod menu) plus 0.7V and ending at 10W at Ubat,min. E.g. UbatMin=2.6V and Power=60W =>
Full 60W until battery voltage is at 3.1V, and then reduced to 50W at 3.0V, 40W at 2.9V and so forth.
When the power is reduced, the battery symbol on the display will toggle with the message "LOW" and
the reduced power level is show. Typical settings for Ubat,min are between 2.5 and 2.7V.
shortly
pressing