Epever Tracer2606BPL 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Epever Tracer2606BPL에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epever Tracer2606BPL 2 페이지. Lithium battery solar charge controller with built in led driver
Epever Tracer2606BPL에 대해서도 마찬가지입니다: 빠른 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (3 페이지), 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

HUIZHOU EPEVER TECHNOLOGY CO., LTD.

※Specific instructions refer to the list of accessories and software.

7. Protection

Protection

Conditions

The PV can be reversely connected with a

controller when:

 Only the PV is connected with the controller;

PV Reverse

 The battery is positively connected, and the

Polarity

open-circuit voltage of the PV is lower than

85V(This requirement is only for

Tracer26/39/5210BPL).

When the PV is not connecting or connection

Battery

reversed, the battery can be reversed.

WARNING: Controller will be damaged when

Reverse

the PV connection is correct and battery

Polarity

connection reversed!

Battery Over

The battery voltage reaches to the OVD

Voltage

Battery Over

The battery voltage reaches to the LVD

Discharge

Temperature sensor is higher than 65℃

Battery

Overheating

Temperature sensor is less than 55℃

Temperature sensor is less than the low

Lithium

temperature value(Default 0℃)

battery Low

Temperature sensor is higher than the low

Temperature

temperature value(Default 0℃)

Load current ≥2.5 times rated current

One short circuit, the output is OFF 5s;

Two short circuit, the output is OFF 10s;

Load Short

Three short circuit, the output is OFF 15s;

Circuit

Four short circuit, the output is OFF 20s;

Five short circuit, the output is OFF 25s;

Six short circuit, the output is OFF

Lithium

Limit current temperature

battery limit

T1＞T2＞T3＞T4＞T5＞T6

current in

low

Limit current I1＞I2＞I3＞I4＞I5＞I6

temperature

8. Technical Specifications

Item

Nominal system voltage

Battery input voltage range

Rated charge current★

Rated charge power

①

Max. PV open circuit voltage

MPP Voltage range

Max. output current

Max. output power

Output voltage range

Load open circuit voltage

Load over voltage protection

Maximum output efficiency

Output current control accuracy

Battery Type

Equalize Charging Voltage

Boost Charging Voltage

Float Charging Voltage

Low Voltage Reconnect Voltage

Low Voltage Disconnect Voltage

Boost Charging Voltage

Low Voltage Reconnect Voltage

Low Voltage Disconnect Voltage

Self-consumption

Temperature compensation coefficient

Communication

Working environment temperature

Enclosure

Overall dimension

Mounting hole size

Mounting dimension

Power cable

Net weight

★The controller has the limit charge current function, the current can be set via the APP software and the remote controller.

Status

The controller is not

damage

Stop charging

stop discharging

Output is OFF

Output is ON

Lithium battery stop

charging/discharging

Lithium battery

charging

Output is OFF

Clear the fault:

Restart the controller

or wait for one

night-day cycle (night

time>3 hours).

When the temperature

is lower than T1, the

charging current is I1;

when the temperature

is lower than T2, the

charging current is I2;

and so on. However,

when the temperature

rises gradually from

Tracer2606BPL

Tracer3906BPL

12/24VDC Auto(Lithium battery do not automatic identification system voltage)

10A

15A

130W/12V;260W/24V 200W/12V;400W/24V 260W/12V;520W/24V 130W/12V;260W/24V

60V( at minimum operating environment temperature ）

46V( at 25℃ environment temperature )

( Battery voltage+2V)～36V

3.3A

4.5A

100W

130W

Lead-acid battery: Sealed(Default) / Gel / Flooded/User; Lithium battery:LiFePO4/ Li-NiCoMn/User

-3mV/℃/2V(Lithium battery don't have temperature compensation coefficient)

124×89×30mm

150×93.5×32.7mm

88×76mm

120×83mm

PV/BAT:14AWG(2.5mm

)

LOAD:18AWG(1.0mm

)

0.54kg

0.73kg

Tel：+86-10-82894896/82894112/+86-752-3889706

9. Troubleshooting

Faults

LED Charging

indicator turn off

during daytime

when sunshine falls

on PV modules

properly

No LED indicator

Battery LED

indicator green fast

Flashing

Battery LED

indicator red

Battery LED

indicator red

flashing

Powering on

normally, the load is

off

The dimming

function is invalid

①When the battery is over discharged, the battery indicator will be red and the load will

be off all the time before the voltage is more than the Low Voltage Reconnect Voltage

(LVRV). In order to judge the system is normal or not, firstly measuring the battery

voltage whether is more than LVRV, if not, restarting the controller to detect the load

whether it is normal.

NOTE: The LVRV can be set, but it must pay more attention that it maybe

damages the battery if the LVRV is too low.

10. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

 PV or load current, voltage or power exceeding the rated value of controller.

 The controller is working temperature exceed the limit working environment

temperature.

 User disassembly or attempted repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Tracer5206BPL

Tracer2610BPL

9～32VDC

20A

100V( at minimum operating environment temperature ）

6.6A

3.3A

200W

100W

( Max. battery voltage+2V)～58V

58V

63V

96%

≤2%

Sealed :14.6V/Gel：No / Flooded:14.8V/User:9-17V (×2/24V)

Sealed :14.4V/Gel：14.2V/Flooded:14.6V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:13.8V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:12.6V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:11.1V/User:9-17V (×2/24V)

LiFePO4:14.5V/ Li-NiCoMn:12.5V / User:9-17V (×2/24V)

LiFePO4:12.8V / Li-NiCoMn:10.5V / User:9-17V (×2/24V)

LiFePO4:11.1V / Li-NiCoMn:9.3V / User:9-17V (×2/24V)

≤15mA/12V;≤22mA/24V

RS485

-40℃～+60℃

IP67

153×105×52.1mm

124×89×30mm

Φ3.5mm

120×94mm

88×76mm

PV/BAT:12AWG(4mm

)

LOAD:16AWG(1.5mm

)

1.18kg

0.54kg

Website：www.epever.com

Possible reasons

Confirm that PV and battery wire

array disconnection

connections are correct and tight

Measure battery voltage with the

Battery voltage maybe

multi-meter. Min.9V can start up the

less than 9V

controller

Check if battery voltage is higher

Battery over voltage

than OVD, and disconnect the PV

When the battery voltage is restored

Battery

to or above LVR point (low voltage

①

reconnect voltage), the load will

over discharged

recover

The controller will automatically turn

the system off. But while the

Battery Overheating

temperature decline to be below 50

º C, the controller will resume.

①The connecting

① Check the connecting cable.

wires are error or

② Check the load's mode and

virtually connected

parameters.

②Load mode is not

③The voltage of LED light is not

appropriate.

within the output voltage range of

③This controller does

controller.

not match with the LED

④Check the connecting cables and

light.

LED light.

④Output short circuit.

The controller does not

①Replace the LED light

match with the LED

②Reduce system rated voltage

light source. This

grade and replace the product

product is a step-up

model

voltage control, If input

For example 24V system change to

voltage is lower than

12V system, and replace the

the rated voltage, it is

corresponding controller

not working.

Tracer3910BPL

10A

15A

200W/12V;400W/24V

92V( at 25℃ environment temperature )

( Battery voltage+2V)～72V

4.5A

130W

150×93.5×32.7mm

120×83mm

PV/BAT:14AWG(2.5mm

)

LOAD:18AWG(1.0mm

)

0.73kg

Any changes without prior notice! Version number：V3.2

T4 to T1, it is

performed at I4.

Troubleshooting

Tracer5210BPL

20A

260W/12V;520W/24V

6.6A

200W

153×105×52.1mm

120×94mm

PV/BAT:12AWG(4mm

)

LOAD:16AWG(1.5mm

)

1.18kg