Epever Tracer3906BPL 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Epever Tracer3906BPL에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epever Tracer3906BPL 2 페이지. Mppt solar charge controller with built-in led driver
Epever Tracer3906BPL에 대해서도 마찬가지입니다: 빠른 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (3 페이지)

페이지 인쇄

NOTE: In the mode of Light ON/OFF and Light ON/Timer, the Load is

turned on after 10Min. delay.

7. Optional Accessories

Accessory 1: Wireless collector (eBox-WL433M-01)

Accessory 2: Super Parameter Programmer—SPP-02.

Use USB to RS485 converter cable: CC- RS485-RS485-150U-22AWG

Accessory 3: PC monitoring setting software "Solar Station Monitor"

 Use USB to RS485 converter cable: CC-USB-RS485-150U-22AWG

Accessory 4: Mobile APP, IAM (Ir-Android-Micro).

 Use USB to RS485 converter cable: CC-USB-RS485-150U-22AWG

 Use OTG cable: OTG-12CM

 APP software can be downloaded from the website of http://www.epsolarpv.com.

Accessory 5: Fixed Plate (Four)

Overall dimension：20×18×6mm/Mounting hole size：Φ3.5mm

Note: Accessory 2-4 can set the controller parameters, please refer to the user

manual of accessory.

8. Protection

Protection

Conditions

PV Reverse

When the battery is correct connecting, the

Polarity

PV can be reversed.

Battery Reverse

When the PV is not connecting, the battery

Polarity

can be reversed.

Battery Over

The battery voltage reaches to the OVD

Voltage

Battery Over

The battery voltage reaches to the LVD

Discharge

Battery

Temperature sensor is higher than 65℃

Overheating

Temperature sensor is less than 55℃

Temperature sensor is less than the low

temperature value(Default 0℃)

Lithium battery

Low Temperature

Temperature sensor is higher than the low

temperature value(Default 0℃)

Load current ≥2.5 times rated current

One short circuit, the output is OFF 5s；

Two short circuit, the output is OFF 10s；

Load Short

Three short circuit, the output is OFF 15s；

Circuit

Four short circuit, the output is OFF 20s；

Five short circuit, the output is OFF 25s；

Six short circuit, the output is OFF

10. Technical Specifications

Item

Model

Nominal system voltage

Battery input voltage range

Rated charge current

Rated charge power

130W/12V;260W/24V

①

Max. PV open circuit voltage

MPP Voltage range

Max. output current

Max. output power

Output voltage range

Load open circuit voltage

Load over voltage protection

Maximum output efficiency

Output current control

accuracy

Battery Type

Equalize Charging Voltage

Boost Charging Voltage

Float Charging Voltage

Low Voltage

Reconnect Voltage

Low Voltage

Disconnect Voltage

Self-consumption

Temperature compensation

coefficient

Communication

Working environment

temperature

Enclosure

Overall dimension

Mounting hole size

Mounting dimension

Power cable

Net weight

※The parameters are in 12V system at 25 º C, please double the values in 24V system; ＃Lithium battery do not automatic identification system voltage and no temperature compensation coefficient.

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

Status

The controller is not

damage

Stop charging

stop discharging

Output is OFF

Output is ON

Lithium battery stop

charging/discharging

Lithium battery

charging

Output is OFF

Clear the fault:

Restart the controller

or wait for one

night-day cycle

(night time>3 hours).

Tracer2606BPL

Tracer3906BPL

10A

15A

195W/12V;390W/24V

58V( at minimum operating environment temperature ）

46V( at 25℃ environment temperature )

( Battery voltage+2V)～36V

3.3A

4.5A

100W

130W

( Max. battery voltage+2V)～58V

58V

63V

Sealed :14.4V/Gel：14.2V/Flooded：14.6V※ ; LiFePO4:14.6V/ Li-NiCoMn:12.51V / User:9-34V

Sealed/Gel/Flooded:13.8V※ ; LiFePO4:14.4V / Li-NiCoMn:12.39V / User:9-34V

Sealed/Gel/Flooded:12.6V※ ; LiFePO4:12.0V / Li-NiCoMn:10.8V / User:9-34V

Sealed/Gel/Flooded:11.1V※ ; LiFePO4:10.6V / Li-NiCoMn:9.3V / User:9-34V

124×89×30mm

150×93.5×32.7mm

88×76mm

120×83mm

PV/BAT:14AWG(2.5mm

0.54kg

0.73kg

Tel：+86-10-82894112 / 82894962 Website：www.epsolarpv.com/www.epever.com

9. Troubleshooting

Faults

LED Charging

indicator turn off

during daytime

when sunshine falls

on PV modules

properly

No LED indicator

Battery LED

indicator green fast

Flashing

Battery LED

indicator red

Battery LED

indicator red

flashing

Powering on

normally, the load is

off

The dimming

function is invalid

①When the battery is over discharged, the battery indicator will be red and the load will be off all the

time before the voltage is more than the Low Voltage Reconnect Voltage (LVRV). In order to judge the

system is normal or not, firstly measuring the battery voltage whether is more than LVRV, if not,

restarting the controller to detect the load whether it is normal.

NOTE: The LVRV can be set, but it must pay more attention that it maybe damages the battery if

the LVRV is too low.

11. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

 PV or load current, voltage or power exceeding the rated value of controller.

 The controller is working temperature exceed the limit working environment

temperature.

 User disassembly or attempted repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Tracer5206BPL

Tracer2610BPL

12/24VDC Auto

＃

9～32VDC

20A

10A

260W/12V;520W/24V

130W/12V;260W/24V

95V( at minimum operating environment temperature ）

6.6A

3.3A

200W

100W

96%

≤2%

Sealed / Gel / Flooded ; LiFePO4 / Li-NiCoMn / User

Sealed :14.6V/Gel：No / Flooded：14.8V※ ; No

≤15mA/12V;≤22mA/24V

＃

-3mV/℃/2V

RS485

-40℃～+60℃

IP67

153×105×52.1mm

124×89×30mm

Φ3.5mm

120×94mm

88×76mm

);LOAD:18AWG(1.0mm

)

1.18kg

0.54kg

Possible reasons

Confirm that PV and battery wire

array disconnection

connections are correct and tight

Measure battery voltage with the

Battery voltage maybe

multi-meter. Min.9V can start up the

less than 9V

controller

Check if battery voltage is higher

Battery over voltage

than OVD, and disconnect the PV

When the battery voltage is restored

Battery

to or above LVR point (low voltage

①

reconnect voltage), the load will

over discharged

recover

The controller will automatically turn

the system off. But while the

Battery Overheating

temperature decline to be below 50

º C, the controller will resume.

①The connecting

① Check the connecting cable.

wires are error or

② Check the load's mode and

virtually connected

parameters.

②Load mode is not

③The voltage of LED light is not

appropriate.

within the output voltage range of

③This controller does

controller.

not match with the LED

④Check the connecting cables and

light.

LED light.

④Output short circuit.

The controller does not

①Replace the LED light

match with the LED

②Reduce system rated voltage

light source. This

grade and replace the product

product is a step-up

model

voltage control, If input

For example 24V system change to

voltage is lower than

12V system, and replace the

the rated voltage, it is

corresponding controller

not working.

Any changes without prior notice! Version number：V1.2

Tracer3910BPL

15A

195W/12V;390W/24V

92V( at 25℃ environment temperature )

( Battery voltage+2V)～72V

4.5A

130W

( Max. battery voltage+2V)～80V

80V

100V

150×93.5×32.7mm

120×83mm

PV/BAT:12AWG(4mm

0.73kg

Troubleshooting

Tracer5210BPL

20A

260W/12V;520W/24V

6.6A

200W

153×105×52.1mm

120×94mm

);LOAD:16AWG(1.5mm

)

1.18kg