Epever Tracer3906BPL 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Epever Tracer3906BPL에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epever Tracer3906BPL 3 페이지. Mppt solar charge controller with built-in led driver
Epever Tracer3906BPL에 대해서도 마찬가지입니다: 빠른 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

HUIZHOU EPEVER TECHNOLOGY CO., LTD.

7. Protection

Protection

Conditions

The PV can be reversely connected with a

controller when:

✓ Only the PV is connected with the

PV Reverse

controller;

✓ The battery is positively connected.

Polarity

The PV's open-circuit voltage is lower

than 85V(This requirement is only for

Tracer26/39/5210BPL).

When the PV is not connecting or the

connection reversed, the battery can be

Battery

reversed.

Reverse

WARNING: Controller will be damaged

Polarity

when the PV connection is correct, and

battery connection reversed!

Battery Over

The battery voltage reaches the OVD

Voltage

Battery Over

The battery voltage reaches the LVD

Discharge

The temperature sensor is higher than 65℃

Battery

Overheating

The temperature sensor is less than 55℃

The temperature sensor is less than the

Lithium battery

low-temperature value(Default 0℃)

Low

The temperature sensor is higher than the

Temperature

low-temperature value(Default 0℃)

Load current ≥2.5 times rated current

One short circuit, the output is OFF 5s;

Two short circuits, the output is OFF 10s;

Load Short

Three short circuits, the output is OFF 15s;

Circuit

Four short circuits, the output is OFF 20s;

Five short circuits, the output is OFF 25s;

Six short circuits, the output is OFF

Lithium battery

Limit current temperature

limit current in

T1＞T2＞T3＞T4＞T5＞T6

low

Limit current I1＞I2＞I3＞I4＞I5＞I6

temperature

8. Technical Specifications

Item

Nominal system voltage

Battery input voltage range



Rated charge current

Rated charge power

Max. PV open circuit voltage

MPP Voltage range

Max. output current



Max. output power

Output voltage range

Load open circuit voltage

Load over voltage protection

Maximum output efficiency

Output current control accuracy

Battery Type

Equalize Charging Voltage

Boost Charging Voltage

Float Charging Voltage

Low Voltage Reconnect Voltage

Low Voltage Disconnect Voltage

Boost Charging Voltage

Low Voltage Reconnect Voltage

Low Voltage Disconnect Voltage

Self-consumption

Temperature compensation coefficient

Communication

Working environment temperature

Enclosure

Dimension

Mounting hole size

Mounting size

Power cable

Net weight

The controller has the charge current limit function. The charge current can be set via the APP software and the remote controller.

 The Max. output power is the same for either the 12V or 24V system, shown above the table.

Status

The controller is no damage

Stop charging

stop discharging

Output is OFF

Output is ON

Lithium battery stop

charging/discharging

Lithium battery charging

Output is OFF

Clear the fault: Restart the

controller or wait for one

night-day cycle (night

time>3 hours).

When the temperature is

lower than T1, the charging

current is I1; when the

temperature is lower than

T2, the charging current is

I2; and so on. However,

when the temperature rises

gradually from T4 to T1, it is

performed at I4.

Tracer2606BPL

Tracer3906BPL

12/24VDC Auto(Lithium battery do not automatically identify system voltage)

10A

15A

130W/12V;260W/24V 200W/12V;400W/24V 260W/12V;520W/24V 130W/12V;260W/24V

60V( at minimum operating environment temperature ）

46V( at 25℃ environment temperature )

( Battery voltage+2V)～36V

3.3A

4.5A

100W

130W

Lead-acid battery: Sealed(Default) / Gel / Flooded/User; Lithium battery:LiFePO4/ Li-NiCoMn/User

-3mV/℃/2V(Lithium battery don't have temperature compensation coefficient)

124×89×30mm

150×93.5×32.7mm

88×76mm

120×83mm

PV/BAT:14AWG(2.5mm

)

LOAD:18AWG(1.0mm

)

0.54kg

0.73kg

Tel：+86-10-82894896/82894112/+86-752-3889706

9. Troubleshooting

Faults

LED Charging

indicator turn off

during daytime

when sunshine

array disconnection

falls on PV

modules properly

Battery voltage may be

No LED indicator

less than 9V

Battery LED

indicator green

Battery over voltage

fast Flashing

Battery

Battery LED

indicator red

over discharged

Battery LED

indicator red

Battery Overheating

flashing

①The connecting wires

are error or

virtually connected

Powering on

②Load mode is not

normally, the load

appropriate.

is off

③This controller does not

match the LED light.

④Output short circuit.

The controller does not

match the LED light

source. This product is

The dimming

step-up voltage control. If

function is invalid

the input voltage is lower

than the rated voltage, it

is not working.

①After the battery is over-discharged, the battery indicator is red. And the load is turned

off all the time until the voltage reaches the Low Voltage Reconnect Voltage (LVRV). To

judge the system is normal or not, firstly measuring whether the battery voltage is higher

than LVRV. If not, restarting the controller to detect whether the load output is normal.

NOTE: The LVRV can be set, but it must pay more attention to modification. Too

low LVLR may damage the battery.

10. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

 PV or load current, voltage, or power exceeds the controller's rated value.

 The controller's working temperature exceeds the limit working environment

temperature.

 User disassembly or attempted to repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Tracer5206BPL

Tracer2610BPL

9~32VDC

20A

100V( at minimum operating environment temperature ）

6.6A

3.3A

200W

100W

( Max. battery voltage+2V)～58V

58V

63V

96%

≤2%

Sealed :14.6V/Gel：No / Flooded:14.8V/User:9-17V (×2/24V)

Sealed :14.4V/Gel：14.2V/Flooded:14.6V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:13.8V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:12.6V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:11.1V/User:9-17V (×2/24V)

LiFePO4:14.5V/ Li-NiCoMn:12.5V / User:9-17V (×2/24V)

LiFePO4:12.8V / Li-NiCoMn:10.5V / User:9-17V (×2/24V)

LiFePO4:11.1V / Li-NiCoMn:9.3V / User:9-17V (×2/24V)

≤15mA/12V;≤22mA/24V

RS485

-40℃～+60℃

IP67

153×105×52.1mm

124×89×30mm

Φ3.5mm

120×94mm

88×76mm

PV/BAT:12AWG(4mm

)

LOAD:16AWG(1.5mm

)

1.18kg

0.54kg

Possible reasons

Confirm that PV and battery wire

connections are correct and tight

Measure battery voltage with the

multi-meter. Min.9V can start up the

controller

Check if the battery voltage is higher

than OVD, and disconnect the PV

When the battery voltage is restored

to or above the LVR point (low

①

voltage reconnect voltage), the load

will recover

The controller will automatically turn

the system off. But while the

temperature decline to be below 50

ºC, the controller will resume.

① Check the connecting cable.

② Check the load's mode and

parameters.

③The voltage of LED light is not

within the output voltage range of

the controller.

④Check the connecting cables and

LED light.

①Replace the LED light

②Reduce system rated voltage

grade, and replace the product

model

For example 24V system change to

a 12V system and replace the

corresponding controller

Tracer3910BPL

10A

15A

200W/12V;400W/24V

92V( at 25℃ environment temperature )

( Battery voltage+2V)～72V

4.5A

130W

150×93.5×32.7mm

120×83mm

PV/BAT:14AWG(2.5mm

)

LOAD:18AWG(1.0mm

)

0.73kg

Website：www.epever.com

Troubleshooting

Tracer5210BPL

20A

260W/12V;520W/24V

6.6A

200W

153×105×52.1mm

120×94mm

PV/BAT:12AWG(4mm

)

LOAD:16AWG(1.5mm

)

1.18kg