Epever Tracer3910BPL 빠른 시작 매뉴얼

{카테고리_이름} Epever Tracer3910BPL에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epever Tracer3910BPL 2 페이지. Mppt solar charge controller
Epever Tracer3910BPL에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (3 페이지), 빠른 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

HUIZHOU EPEVER TECHNOLOGY CO., LTD.

※Thank you for selecting the Tracer BPL series lithium battery

MPPT solar charge controller with built-in LED driver. Please read

this manual carefully before using the product and pay attention to

the safety information.

MPPT Solar Charge Controller

1. Overview

The Tracer BPL series lithium battery MPPT solar charge controller combines solar

charge controller and LED constant current driver into one unit which is ideal for solar

LED Lighting, especially when dimmer function is needed. The advanced Maximum

Power Point Tracking charging methods enables the system charging and discharging

management to obtain the most radical optimization. Increase the system flexibility, yet

lower down the system cost. The features are listed below:

 Adopt high quality components of ST,IR and Infineon, make sure product using

lifespan

 Wide working environment temperature(-40℃～60℃)

 Apply to lead-acid battery and lithium battery

 Lithium battery self-activating and low temperature protection function

 Maximum conversion efficiency of 98%

 Advanced Maximum Power Point Tracking (MPPT) technology, with tracking

efficiency no less than 99.5%

 Ultra-fast tracking speed and guaranteed tracking efficiency

 Accurately recognizing and tracking of multiple power points

 Lithium battery low temperature protection function

 Lithium battery limit current in low temperature

 Digital precision constant current control and the control accuracy are less than ±2%

 Intelligent power mode with 365-day lighting control technology

 Load reduce power automatically

 Maximum output efficiency of 96%

 PV and Load power limitation function

 The output current can be adjusted among the rated power and current range

 Monitoring and setting parameter via Mobile APP, PC Monitor setting software with

RS485 communication interface.

 Use of standard Modbus communication protocol for RS485 bus connections,

communication protocol compatibility much better

 Connecting the IOT(Internet of Things) module and Cloud Server monitoring software

to realize remote monitoring of the multi-machine system

 The RS485 connector can provide power supply

 Aluminum housing for better cooling

 Real-time energy statistics function

 IP67 waterproof degree

2. Product Features

⑴

①

Temperature Sensor

②

PV Positive and Negative Wires

③

Battery Positive and Negative Wires

④

Load Positive and Negative Wires

(1)The temperature sensor short-circuited or damaged, the controller will be charging or

discharging at the default temperature 25 º C.

(2)The port can provide the DC power supply of 5VDC/150mA and have the short circuit

function.

NOTE: When the RS485 communication port is not working, the

waterproof cap must be installed to prevent water getting in.

3. Wiring

 Reference for Serial connection of LED

System

Serial connection

Voltage

5～18 LED

12V

10～18 LED

24V

NOTE: The above one LED (1W, 3.3V) is calculated. If the user uses the

unconventional LED, The actual LED voltage must less than the Max.

Load Output Voltage.

WARNING：DO NOT electric shock! The product built-in boost LED driver,

the output voltage is higher than the human safety voltage.

---with built-in LED Driver

⑤

Charging Status LED indicator

⑥

Battery Status LED indicator

⑵

⑦

RS485 waterproof port

⑧

Waterproof cap(Included)

Max. Output

Min. Output Voltage

Voltage

15V

60V

30V

60V

Tel：+86-10-82894896/82894112/+86-752-3889706

 Connection Order

1) Connect components to the charge controller in the sequence as shown above and

pay much attention to the "+" and "-". Please don't insert the fuse or turn on the breaker

during the installation. When disconnecting the system, the order will be reserved.

2) After power on the controller, check the battery LED indicator on the controller, it will

be green. If it's not green, please refer to chapter 9.

3) Connecting a fuse in series through battery positive (+) in the circuit and the battery

circuit fuse must be 1.25 to 2 times to the rated current. The installed distance is within

150mm.

4) The process of charging and discharging can't operate simultaneously, and the

discharge process is prior to charging.

 Load self-test function

The load is ON when the controller power on 10seconds. After 10 seconds it will restore

to set working mode.

4. LED Indicators

Indicator

Color

Green

Orange

Red

Orange

All indicators

and

green

5. Load Working Mode

1) Manual Mode

2) Light ON/OFF(Default)

3) Light ON + Timer

Light ON + Timer1

Light ON + Timer2

Light ON + Timer3

4) Real-time Control

Control the load ON/OFF time through setting real-time clock.

5) Lntelligent Power Mode

After the mode of intelligent power reduction is turned on and the capacity of the storage

battery is lower than 50%, the LED load will make adjustment by automatically reducing

the power in a linear manner according to the capacity of the storage battery, and mean

while the load will operate based on the minimum value between the set value and the

value after power reduction. Moreover, the mode of intelligent power reduction will be

exited after charging is started on the next day.

NOTE: In the mode of Light ON/OFF and Light ON/Timer, the Load is

turned on after 1Min. delay,the delay time can be set.

6. Accessories(optional) and Software

1）PC Software(www.epever.com ——Solar Station Monitor)

2）APP Software

 Android phone(www.epever.com——ChargeController(Li) )

 IPhone(APP Store——EPEVER——EP-01)

※MT50 does not support the relevant parameters of lithium battery.

Website：www.epever.com

Status

Instruction

PV connection normal

but low

On Solid

voltage(irradiance)

from PV, no charging

No PV voltage(night

OFF

time) or PV connection

problem

Slowly Flashing(1Hz)

In charging

Fast Flashing(4Hz)

PV Over voltage

On Solid

Normal

Slowly Flashing(1Hz)

Full

Fast Flashing(4Hz)

Over voltage

On Solid

Under voltage

Over discharged

On Solid

Low temperature

Fast Flashing(4Hz)

Battery Overheating

Set parameters

Flashing two times

successfully

Turn-On voltage (Adjustable):

5V(12Vsystem),delay10min.

Turn-Off voltage (Adjustable):

6V(12Vsystem),delay10min.

Note:24V system voltage×2