EPH Controls R27-HW 운영 지침

{카테고리_이름} EPH Controls R27-HW에 대한 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. EPH Controls R27-HW 2 페이지. 2 zone programmer
EPH Controls R27-HW에 대해서도 마찬가지입니다: 운영 지침 (2 페이지), 설치 지침 (2 페이지)

페이지 인쇄

R27-HW - 2 Zone Programmer

Contents

Factory default settings

Factory program settings

Resetting the programmer

Setting the date and time

ON/OFF period selection

Adjusting the program settings

Copy function

Reviewing the program settings

Boost function

10. Advance function

11. Holiday mode

12. Backlight mode selection

13. Keypad lock and unlock

14. Frost protection function

15. Master reset

1. Factory default settings

Program:

5/2D

Backlight:

Keypad:

Unlocked

Frost Protection:

2. Factory program settings

P1 ON

P1 OFF

Mon-Fri

Sat-Sun

7:30

10:00

All 7 days

P1 ON

P1 OFF

Everyday

P1 ON

P1 OFF

3. Resetting the programmer

It is necessary to press the RESET button prior to initial programming.

This button is located behind the cover on the front of the unit.

4. Setting the date and time

Lower the cover on the front of the unit.

Move the selector switch to the CLOCK SET position.

Press the

buttons to select the day.

Press the

buttons to select the month.

Press the

buttons to select the year.

Press the

buttons to select the hour.

Press the

buttons to select the minute.

Press the

buttons to select 5/2D, 7D or 24H

The date, time and function are now set. Move the selector switch to the

RUN position to run the program, or to the PROG SET position to change

the program setting.

Important: Keep this document

This 2 zone programmer is designed to

provide ON/OFF control for both Hot

Water and Heating, with the value added

application of in built frost protection.

5/2D

P2 ON

P2 OFF

P3 ON

12:00

17:00

P2 ON

P2 OFF

P3 ON

24H

P2 ON

P2 OFF

P3 ON

RUN

CLOCK

SET

Press

EPH Controls Ireland

[email protected] www.ephcontrols.com

5. ON/OFF period selection

There are 4 modes available on this programmer for users to choose for their

individual application.

AUTO

The programmer operates 3 'ON/OFF' periods per day.

ALL DAY The programmer operates 1'ON/OFF' period per day.

This operates from the rst ON time to the third OFF time.

The programmer is permanently on. **ON**

OFF

The programmer is permanently o . **OFF**

P3 OFF

Lower the cover on the front of the unit. By pressing the

you can change between AUTO / ALL DAY / ON / OFF for HOT WATER.

23:00

Repeat this process for HEATING by pressing the

P3 OFF

6. Adjusting the program settings

Lower the cover on the front of the unit.

P3 OFF

Move the selector switch to the PROG SET position.

You can now program the HOT WATER.

Press the

Repeat this process to adjust the ON & OFF times for P2 & P3.

Press

SELECT

When completed, move the selector switch to the RUN position.

PROG

7. Copy function

SET

Copy function may only be used if the programmer is in the 7d mode.

Lower the cover on the front of the programmer.

Move the selector switch to the PROG SET position.

Set the ON & OFF times for the day of the week you wish to copy from.

COPY

Press the

Holiday

Press the

button to copy the ON & OFF to this day.

Press the

button to skip a day.

ON & OFF times can be copied to multiple days by using the

Press the

button when copying has been completed.

When completed, move the selector switch to the RUN position.

EPH Controls UK

[email protected] www.ephcontrols.co.uk

Page 1 of 2

Operating Instructions

CAUTION!

Before commencing, disconnect the

device from the mains. There are parts that

carry mains voltage behind the cover. Never

leave unsupervised when it is open. (Prevent

non specialists and especially children from

gaining access to it.)

Never remove this product from the

electrical baseplate. Disconnect from mains

supply in the event of any damage to any

buttons. Do not use sharp tools to push any

button.

buttons to adjust the P1 ON time.

buttons to adjust the P1 OFF time.

and repeat the above process to adjust for HEATING.

button for 2 secs. The next day of the week will begin to ash.

button,

SELECT

button.

SELECT

RUN

CLOCK

PROG

SET

Press

RUN

CLOCK

PROG

SET

button.

20180621_R27-HW_OpIns_JW