EPH Controls R37-RF 운영 지침

{카테고리_이름} EPH Controls R37-RF에 대한 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. EPH Controls R37-RF 2 페이지. 3 zone rf programmer
EPH Controls R37-RF에 대해서도 마찬가지입니다: 운영 지침 (2 페이지)

EPH Controls R37-RF 운영 지침
R37-RF - 3 Zone RF Programmer
Contents
1.
Factory default settings
2.
Factory program settings
3.
Resetting the programmer
4.
Setting the date and time
5.
ON/OFF period selection
6.
Adjusting the program settings
7.
Reviewing the program settings
8.
Boost function
9.
Advance function
10. Holiday mode
11. Connect RF thermostat with the programmer
12. Disconnect RF thermostat from the programmer
13. Backlight mode selection
14. Keypad lock and unlock
15. Copy function
16. Frost protection
17. Master reset
1. Factory default settings
Program:
5/2D
Backlight:
On
Keypad:
Unlocked
Frost Protection:
O
2. Factory program settings
P1 ON
P1 OFF
Mon-Fri
Sat-Sun
7:30
10:00
All 7 days
P1 ON
P1 OFF
Everyday
P1 ON
P1 OFF
3. Resetting the programmer
It is necessary to press the RESET button prior to initial programming.
This button is located behind the cover on the front of the unit.
4. Setting the date and time
Lower the cover on the front of the unit.
Move the selector switch to the CLOCK SET position.
Press the
or
buttons to select the day.
Press the
or
buttons to select the month.
Press the
or
buttons to select the year.
Press the
or
buttons to select the hour.
Press the
or
buttons to select the minute.
Press the
or
buttons to select 5/2D, 7D or 24H
The date, time and function are now set. Move the selector switch to the
RUN position to run the program, or to the PROG SET position to change
the program setting.
5. ON/OFF period selection
There are 4 modes available on this programmer for users to choose for their
individual application.
Important: Keep this document
This 3 zone RF programmer is designed to
provide ON/OFF control for 3 zones, with
the value added application of in built
frost protection.
5/2D
P2 ON
P2 OFF
P3 ON
12:00
12:00
17:00
7D
P2 ON
P2 OFF
P3 ON
24H
P2 ON
P2 OFF
P3 ON
RUN
CLOCK
SET
Press
Press
Press
Press
Press
Press
EPH Controls Ireland
[email protected] www.ephcontrols.com
5. ON/OFF period selection
AUTO
The programmer operates 3 'ON/OFF' periods per day.
ALL DAY The programmer operates 1'ON/OFF' period per day.
This operates from the rst ON time to the third OFF time.
ON
The programmer is permanently on. **ON**
OFF
The programmer is permanently o . **OFF**
Lower the cover on the front of the unit. By pressing the
you can change between AUTO / ALL DAY / ON / OFF for Zone 1.
P3 OFF
Repeat this process for Zone 2 by pressing the
Zone 3 by pressing the
23:00
6. Adjusting the program settings
P3 OFF
Lower the cover on the front of the unit. Move the selector switch to the
PROG SET position. You can now program zone 1.
P3 OFF
Press the
Press the
Repeat this process to adjust the ON & OFF times for P2 & P3.
Press
Press
3
When completed, move the selector switch to the RUN position.
PROG
7. Reviewing the program settings
SET
Lower the cover on the front of the unit.
Move the selector switch to the PROG SET position.
By pressing
Zone 1.
Press
Press
3
When completed, move the selector switch to the RUN position.
8. Boost function
This function allows the user to extend the ON period for 1, 2 or 3 hours.
If the zone that you wish to Boost is timed to be OFF, you have the facility to
switch it ON for 1, 2 or 3 hours.
Press the required button,
- once, twice or three times respectively.
To cancel the boost function, simply press the respective boost button again.
EPH Controls UK
[email protected] www.ephcontrols.co.uk
Page 1 of 2
Operating Instructions
CAUTION!
Before commencing, disconnect the
device from the mains. There are parts that
carry mains voltage behind the cover. Never
leave unsupervised when it is open. (Prevent
non specialists and especially children from
gaining access to it.)
Never remove this product from the
electrical baseplate. Disconnect from mains
supply in the event of any damage to any
buttons. Do not use sharp tools to push any
button.
(Continued)
button.
3
or
buttons to adjust the P1 ON time.
buttons to adjust the P1 OFF time.
or
and repeat the above process to adjust for Zone2.
and repeat the above process to adjust for Zone3.
this will review each of the ON/OFF times for P1 to P3 for
and repeat the above process to adjust for Zone 2.
and repeat the above process to adjust for Zone 3.
ZONE
ZONE
for Zone 1,
for Zone 2 and
1
2
Boost
Boost
button,
button and for
RUN
CLOCK
PROG
SET
SET
Press
Press
RUN
CLOCK
PROG
SET
SET
ZONE
for Zone 3.
3
Boost
20180621_R37-RF-OpIns_JW