DieHard Portable Power 750 운영자 매뉴얼 - 페이지 6

{카테고리_이름} DieHard Portable Power 750에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DieHard Portable Power 750 7 페이지. 12v dc power source and jump starter
DieHard Portable Power 750에 대해서도 마찬가지입니다: 운영자 매뉴얼 (8 페이지), 소유자 매뉴얼 (8 페이지)

페이지 인쇄

IMPORTANT: Using the Engine Start feature

without a battery installed in the vehicle will

damage the vehicle's electrical system.

1. Turn the ignition OFF.

2. Lay the DC cables away from any

fan blades, belts, pulleys and other

moving parts.

3. For a negative-ground vehicle (as in most

vehicles), connect the Portable Power's

POSITIVE (RED) clamp to the POSITIVE

(POS, P, +) battery post. Next, connect

the NEGATIVE (BLACK) clamp to the

vehicle chassis or engine block, away

from the battery.

4. For a positive-ground vehicle, connect the

Portable Power's NEGATIVE (BLACK)

clamp to the NEGATIVE (NEG, N, -)

battery post. Next, connect the POSITIVE

(RED) clamp to the vehicle chassis or

engine block away from the battery.

5. Turn the rotary switch to the ON position.

6. Crank the engine for no more than

8 seconds. If the engine does not start,

wait 2 minutes before cranking again.

7. After the engine starts, turn the switch to

the OFF position and remove the Portable

Power from the battery.

8. Charge the Portable Power.

USING THE USB PORT

The USB port provides up to 2.1A at 5V DC.

1. Make sure the battery clamps are

securely clipped on the storage holders.

2. To turn on the USB, press the battery

status button. The battery status LED will

illuminate when the USB is on.

3. Plug your device into the USB port.

4. When finished using the USB port,

press the Battery Status button to turn off

the USB.

5. Charge the Portable Power.

USING THE WORK LIGHT

The work light is controlled by a switch

located on the front of the Portable Power.

• Make sure the light is turned OFF when the

unit is being recharged or stored.

• Position the Portable Power on a flat, stable

surface near the intended work area.

• Ensure the battery clamps are securely

clipped on the storage holders.

USING THE PORTABLE POWER

•

POWERING A 12V DC DEVICE

The Portable Power is a power source for

all 12V DC accessories that are equipped

with a 12V accessory plug. Use it for power

outages and on fishing or camping trips.

NOTE: Do not power a 12V device with the

Portable Power while charging the internal

battery.

1. Make sure the device to be powered

is OFF before inserting the 12V DC

accessory plug into the 12V DC

accessory outlet.

2. Open the protective cover of the DC power

outlet on the Portable Power.

3. Plug the 12V DC device into the DC

power outlet and turn on the 12V DC

device (if required).

4. When finished, turn off the DC device

(if required) and unplug from the DC

power outlet.

CAUTION: Do not use the Portable Power

to run appliances that draw more than

15A DC.

NOTE: Extended operation of a 12V DC

device may result in excessive battery

drain. Recharge the Portable Power

immediately after unplugging the 12V

DC device.

ESTIMATED RUN-TIMES

PPLIANCE

TYPE

Cell phone

Fluorescent

light

Radios, fans

Depth finder

Camcorder

Electrical tool

Electric cooler

Car vacuum,

air compressor

NOTE: Actual time may vary. Times are based on the

internal battery being fully charged.

•

ESTIMATED

EST WATTAGE

RUN TIME

4 watts

21 hrs

4 watts

21 hrs

10 watts

8.4 hrs

10 watts

8.4 hrs

15 watts

5.6 hrs

24 watts

3.5 hrs

48 watts

1.8 hrs

80 watts

1.1 hrs