EPHREM LE NOMADE 120 조립 지침

{카테고리_이름} EPHREM LE NOMADE 120에 대한 조립 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. EPHREM LE NOMADE 120 2 페이지.

페이지 인쇄

L E N O M A D E 1 2 0

⑦

③

④

②

⑤

①

⑥

⑧

⑨

⑧

• 10 cm breeze blocks for the insulation with

vermiculite concrete (load bearing slab:

L166xD151)

• 20 cm breeze blocks for the insulation with

rock/ceramic wool + sand (load bearing slab:

L186xD161)

20cm breeze

blocks

EXPLODED VIEW

WARNING: DO NOT USE ALCOHOL, GASOLINE, OR SIMILAR FLAMMABLE LIQUIDS TO IGNITE OR REKINDLE THE FIRE

⑫

⑪

Total weight: 430 kg

Packaged on a pallet

measuring 110×130 cm

15 to 20 cm thick above

the dome

Dry sand

Rock wool in flexible rolls

⑬

The combination of rock

wool + sand can be

replaced by vermiculite

concrete)

20 cm load

⑨

bearing slab

⑩

Layer of lean mortar

(non-refractory)

1 dose of normal

cement to 6 doses

of 0/4 mm sand.

A S S E M B LY I N S T R U C T I O N S

134

Step 1:

Trim elements if needed with a wood rasp.

Step 2:

Build a concrete slab

for insulation with vermiculite concrete) and let it dry for at least 22 days. Create a thin bed

lean mortar

(2 to 3 cm thick) using standard cement

depicted in ﬁgure 1 to place the 22 base slabs

mortar bed. Make sure they are properly aligned and that the top surface is leveled. No

joint mortar is required. Remove any excess mortar from around the base.

to dry for 24 to 48 hours before proceeding.

Step 3:

Position the front element

②, ③, ④,

install the elements

below or between these elements. Fit the element

with the center of part ①. Secure the metal strapping to the base of element

Ⓑ

Ⓓ

bolts

and tighten them

other.

Step 4:

Build a wall surrounding the oven using breeze blocks that are 20 cm thick (10 cm

for insulation in vermiculite concrete). Make sure to leave a 5 cm gap between the slabs

and the breeze blocks to allow for expansion.

Step 5:

Position the smoke drain-façade

indicated. Be cautious not to overtighten the bolts; tighten them fully with a spanner and

then unscrew them by half a turn.

Step 6:

Assemble the 200 mm stainless steel ﬂue pipe and connect it to the designated

space ⑫. Ensure a secure ﬁt and seal the connection using

Step 7:

Surround the entire oven with a 10 cm ﬂexible roll of rock/ceramic wool or of

EPHREM insulating ﬁbre (available as an option). Cover the insulation with 0/4 dry sand or

vermiculite concrete, ensuring it reaches a minimum height of 20 cm above the dome

Step 8:

Leave an air gap of 20 cm between the roof and the top of the oven insulation to

create a decompression chamber. Additionally, insulate the load-bearing slab from

underneath with a single rigid panel of at least 5 cm thick rock wool. Finally, build the

desired cladding to complete the installation.

134

⑩

measuring at least W195xD165x20 cm (W175xD155x20

⑨.

Follow the conﬁguration

⑧

moistened beforehand on top of the

①

according to the provided diagram. Proceed to

⑤

⑥

and

in the speciﬁed order, ensuring there are no joints

⑦

without a joint, aligning the mark

to ensure a snug ﬁt of the oven side elements against each

⑪

and secure it in place using the four bolts

refractory

Allow the ﬂoor

Ⓐ

①

using the

Ⓒ

mastic.

⑬.