Olympus CAMEDIA E-100 RS 문제 해결

{카테고리_이름} Olympus CAMEDIA E-100 RS에 대한 문제 해결을 온라인으로 검색하거나 PDF를 다운로드하세요. Olympus CAMEDIA E-100 RS 3 페이지. E-100rs guide rapide de d謡rrage (fran栩s)
Olympus CAMEDIA E-100 RS에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 연결 매뉴얼 (9 페이지), 소프트웨어 설치 매뉴얼 (2 페이지), (빠른 시작 가이드 (2 페이지), (프랑스어) 수동 라피드 드 데마라주 (2 페이지)

DOCUMENT NUMBER 2039

EXTERNAL FLASH OR STROBES NOT FIRING WITH OLYMPUS CAMERAS

1. Make sure the camera and external flash/strobe settings are setup as follows:

C-2000 Zoom:

You can use any flash which is PC Sync compatible and can be set to F2 thru F11. Plug the PC

cord into the camera's PC Sync socket. Turn the camera mode dial to "A" Aperture Priority

mode (IMPORTANT: External flash can only be used in Aperture Mode!!!). Turn on the flash

and set the aperture (F-stop ) and/or ISO settings to match the settings used on the camera.

C-2020 Zoom:

IMPORTANT: The default setting for the External Flash setting is OFF. To connect any

external flash/strobe, you need to activate this setting.

You can use any flash which is PC Sync compatible and can be set to F2 through F11. Plug the

PC cord into the camera's PC Sync socket. Set the mode dial to A/S/M. Turn on the extension

flash. Select Aperture Priority or Manual mode on the camera ("P" mode would also work but

you wouldn't know what settings to use on the external flash). Press the menu button, and then

press the top/bottom arrows on the jog dial to select the External Flash mode (2nd selection on

menu 1/3). Press the right arrow on the jog dial, and then press the top/bottom arrow to select

"Auto" or "Fill-in" Flash mode. Press the "OK button to set this selection. Set the external flash

to the same aperture and/or ISO settings as the camera.

C-2040/3000/3030/3040 Zoom, C-2100/C-700 UZ and E-100RS:

The above cameras utilize a 5-pin TTL connector for the external flash connection. The 5-pin

TTL connector is designed to control the Olympus FL-40 dedicated flash unit (p/n 200596). To

use the FL-40 with these cameras, the optional Olympus FL-CB01 cable (p/n 200 664) and FL-

BK01flash bracket (p/n 200 666) must be used.

The 5-pin TTL connector can also control a PC Sync flash or strobe system by using the optional

FL-CB04 flash cable (p/n 200 661). Since this type of flash/strobe is non-dedicated, the

photographer will need to manually match the flash output with the camera.

Set the camera mode dial to P or A/S/M. Turn on the extension flash unit's power then select the

camera's flash mode. Using the camera's menus you may select built-in + extension flash

Olympus America Inc.

Page 1 of 3

T W O C O R P O R A T E C E N T E R D R I V E

M E L V I L L E , N Y

1 1 7 4 7 - 3 1 5 7

D I G I T A L T E C H N I C A L S U P P O R T

C O N S U M E R P R O D U C T S G R O U P

( 8 8 8 ) 5 5 3 - 4 4 4 8

h t t p : / / s u p p o r t . o l y m p u s a m e r i c a . c o m

Last updated on 11/05/02