Olympus CX21 유지 관리 매뉴얼 - 페이지 18

{카테고리_이름} Olympus CX21에 대한 유지 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Olympus CX21 25 페이지. Education microscope
Olympus CX21에 대해서도 마찬가지입니다: 사용 설명서 (28 페이지)

페이지 인쇄

CX21 MAINTENANCE MANUAL

2-2 Adjustment method for the tension of X-wire

(B)

(a)

< Fig. 1 >

(C)

•@•@•@•@•@•@•@

2-3 Adjustment method for the tension of Y-wire

•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@

(C)

•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@

(B)

(b)

•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@

Confirmation of X/Y-wire tension in observation state :

1) After checking the above condition, Install the mechanical stage to the plane stage in reverse

•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@•@

order of disassembly 1) on page 14, set the microscope at observation state and check that

image is brought into the desired position without backlash (2 microns: with100 X objective).

2) If it is out of standard, repeat the above procedures until the condition is satisfied.

3) In case where the image backlash can not be eliminated, perform the knob tension adjustment

referring to 2-4 on page 16.

(A)

(D)

*Check that Y-knob (C) is

rotated following the

movement of Y-body-1(D)

when moving the Y-body-1

in stroke by a hand.

*Push the wire (B) to the

wall (b) to check the tension

in the same manner as

X-wire.

(A)

(D)

1) Loosen the screws (*1) securing the holder

(A).

Screws: CUK 3X6SA (*1) 2pcs.

2) Adjust the tension of the X-wire (B) by

moving the holder (A) in arrow directions as

shown in the left figure.

3) Temporarily tighten the screws (*1).

4) Check the tension of X-wire if it is too tight or

loose while pushing the X-wire (B) to the

wall (a) in arrow direction. <Fig.1>

If the tension of wire is loose, slip may occur

between the X-knob and X-wire.

Therefore, check that X-knob (C) is rotated

following the movement of guide (D) when

moving the guide in stroke by a hand.

If the tension is too tight and the X-wire does

not come in contact with wall (a) due to no

deflection, it may cause image backlash.

Therefore, confirm it in observation state as

described below.

1) Loosen the screws (*1) securing the holder

(A)

Screws: CUK 3X6SA (*1) 2pcs.

2) Adjust the tension of the Y-wire (B) by

moving the holder (A) in arrow directions as

shown in the left figure.

3) Temporarily tighten the screws (*1).

4) Check the tension of Y-wire if it is too tight or

loose while pushing the Y-wire (B) to the

wall (b) in arrow direction.

- 15 -

REPAIR PROCEDURE