Olympus IPLEX LX 참조 매뉴얼 - 페이지 2

{카테고리_이름} Olympus IPLEX LX에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Olympus IPLEX LX 3 페이지. Industrial videoscope

페이지 인쇄

Distance mode is for measuring the line segment between

two measurement points

1. Place the cursor on one end of the line segment and press

MEAS/ENTER on the joystick to specify point A.

2. Place the cursor on the other end of the line segment and press

MEAS/ENTER on the joystick to specify point B.

The length of line segment A-B is displayed.

B POINT-TO-LINE

C OFFSET (FX only)

Perpendicular

distance

Point-to-Line and offset mode are for measuring the distance

from a measurement point to the reference line defined by

two points. In Offset mode, an offset line will additionally be

displayed from the measurement point, in parallel to the

reference line.

1. Place the cursor on both ends of the line segment and press

MEAS/ENTER on the joystick to specify points A and B.

Reference line A-B is shown.

2. Place the cursor on the point from which you want to measure the

distance to reference line A-B and press MEAS/ENTER on the

joystick to specify point C.

The distance between reference line A-B and point C (or Offset

Line) is displayed. (Offset mode is only available for IPLEX FX

models.)

D DEPTH

Depth or height

Depth mode is for measuring the distance from a

measurement point to the reference plane defined by three

reference points.

1. Place the cursor on points A, B and C to define the reference

plane, then press MEAS/ENTER on the joystick to specify points

A, B and C.

Reference plane ABC is shown.

2. Place the cursor on the point from which you want to measure the

distance to reference plane ABC and press MEAS/ENTER on the

joystick to specify measurement point D.

The distance between reference plane ABC and point D is

displayed. A positive value (height) means the point is closer to

the tip of the scope than the reference plane, and a negative

value (depth) means the point is farther away.

point

Measurement

point

Distance

Reference

line

Reference

point

Measurement

point

Offset Line

(Offset Only)

Reference

point

Reference

point

Reference

surface

Measurement

Reference

point

Area mode is for measuring the area defined by multiple

measurement points. Lines mode is for measuring the total

length of lines defined by multiple measurement points.

Place the cursor on points to define the area/lines and press

MEAS/ENTER on the joystick to specify the measurement points.

The total length of lines defined by multiple measurement points is

displayed at the bottom of the screen.

Note:

Up to 20 measurement points can be specified per measurement

session.

When measuring an area, one additional point must be positioned to

define the complete subject outline. This point (point 6 in the example

above) needs to be located where the line between this point and the

last point (point 5) cross across the first drawn line.

The area enclosed by lines is displayed at the bottom of the screen.

F PROFILE (FX only)

Profile mode is for displaying the surface profile of a line

connecting two points.

1. Place the cursor on both ends of the

line whose surface profile you want to

inspect and press MEAS/ENTER on

the joystick to specify the two points.

The surface profile obtained by

sectioning a target object with the plane

defined by the line connecting two

specified points and the optical center

is displayed. The surface profile

graphics overlaid on the right screen

show the profile viewed from the

direction perpendicular to the optic

axis.

G MULTI (FX only)

Reference point

Width

Reference point

Multi mode automatically detects and displays the

measurement values of a region specified by two

reference points. The width, depth and surface area

of any missing material will be measured.

1. Place the cursor on each side of the material loss and press

[MEAS/ENTER] on the joystick to specify the reference points.

The region of missing material will be drawn in the left and right

screen. The width, depth and area dimension of missing material

will be displayed at the bottom of screen.

SAVING YOUR STEREO

MEASUREMENT RESULT

•

Press and hold the [FRZ/REC] button for at least two seconds to

save your stereo measurement image with the measurement

result.

•

"STILL" indicator will confirm that the image was recorded.

•

Press [VIEW] button to display the saved image at any time.

Measurement

point

Measurement

point

Area

Depth