Axminster 951810 지침 - 페이지 2

{카테고리_이름} Axminster 951810에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Axminster 951810 2 페이지. Empress pen kits

페이지 인쇄

Instructions for the pen kits...

Kit No's. 951809-951810 Empress

Pictures of samples of the finished articles, in both timber and acrylic, can be found

in our catalogue in the 'Woodturning Projects' Section.

Below is a list of the items required to make the finished items from the purchased

kits (Not including the body blanks). If you do not possess these items we have

offered our catalogue stock code numbers alongside the items as a quick guide.

We have tried to include everything in the list, although we realise that many

woodturners will already have most of them.

Fully read manual

Ear protection

Eye protection

and safety instructions

should be worn

before use

Required items...

Alternatives are listed to cater for different lathe configurations.

Deluxe Pen Mandrel 1MT

Deluxe Pen Mandrel 2MT

60˚ Live Tail Stock Centre 1MT

60˚ Live Tail Stock Centre 2MT

60˚ Live Tail Stock Centre 3MT

Bushing Set (4 pieces)

11/32" drill bit

15mm drill bit

Axminster Universal Barrel Trimmer

2 Part Rapid Epoxy Resin Adhesive

Alternative Zap-A-Gap Adhesive (Cyanoacrylate)

Recommended accessories...

Quick Action Pen Blank Vice

Pen Blank Sizing and Cutting Jig

Axminster Pen Assembly Press

Using 19mm (3/4") Square stock; cut the blanks to the length of the brass tubes

adding 2-3mm to allow for trimming. A Pen Blank Sizing and Cutting Jig makes

thisprocess very much easier.

Drill an 15mm diameter hole through the centre of the shorter blank and an 11/32"

hole through the longer one. Care must be taken not to force the drill bit, (this may

cause it to 'wander' from the centre line), and remember to back out the drill

frequently to clear the debris from the hole. If you are using a pillar drill the Quick

Action Pen Blank Vice is a very useful accessory for this task, it ensures that the

blank is held upright and firmly in position. Moreover, if the vice is clamped to the

table of the drill, it will provide accurate repeatability for all the blanks that require

drilling.

When the holes are drilled, spread the adhesive randomly over the brass tubes

and insert the tubes into the blanks using a twisting motion to ensure the glue is

Dust mask

Foot protection

spreadevenly between the two surfaces. Over insert the tubes into the blanks by

should be worn

approximately 1mm giving an allowance for the blank to be trimmed to size and

the excess glue to be removed. Using the Barrel Trimmer, trim the ends of the

blanks squarely and neatly to the ends of the brass tubes; this will also remove any

excess glue that may have exuded from the joint. Take care not to undercut the

brass tubes.

Code No:

211322

211323

Slide a mandrel spacer bush onto the shaft, add a 16.5mm diameter bush from

340202

the bushing set and add the 15mm 'tubed' blank. Next add the matching bush

340203

followed by the 15mm diameter bush, add the 11/32" 'tubed' blank and the other

340204

15mm diameter bush.

951820

Slide a mandrel spacer bush up to the assembly and add the locking nut. Tighten

702557

the locking nut to allow the assembly to be turned without 'creeping' . Do not

702584

overtighten, this may cause the assembly to distort and you will not achieve

700265

accurate alignment.

340282

990095

600771

16.5mm

600623

200205

Preparing the blanks...

Setting up the mandrel for turning...

16.5mm

15mm

Turning the blanks...

Turn both blanks to the desired shape leaving slightly proud at the bushings. Sand

the blanks using progressively finer grits of abrasive until the desired finish is

achieved then apply your chosen finish. If using polyester or acrylic pen blanks we

recommend using Micro-Mesh abrasives used wet.

• Layout the parts as in the diagram below paying attention to any grain alignment

requirements on the blanks.

• Press the end cap into the back end of the longer tube.

• Slide the trim ring as shown below over the unthreaded end of the nib coupler,

then press them into the end of the longer tube.

• Rollerball pen: Insert the spring then the ink refill into the long tube. Fountain

pen: Attach the ink cartridge to the back of the fountain nib.

• Thread the Rollerball or fountain nib into the nib coupler.

• Press the cap/clip into the short tube.

• Press the centre band coupler into the other end of the short tube to complete

the pen.

(See parts diagram on reverse side)

15mm

Pen assembly...