Axminster AW422J 사용자 설명서 - 페이지 8

{카테고리_이름} Axminster AW422J에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Axminster AW422J 8 페이지. 10-22mm narrow crown stapler

페이지 인쇄

Specific Safety Instructions for the Stapler...

A X M I N S T E R

W H I T E

If your air system does not use PCL fittings, and you have reason to change the connecting

method of the tool to your air supply, ensure that the new connector will not allow pressure

to be retained in the tool.

Ensure the supply does not exceed the maximum permissible pressure.

There is no safety enable with this tool, there is only a manual safety connected to the

trigger. Once the safety lock has been removed (a conscious action), the stapler will fire

when the trigger is pressed.

Do not use staples outside the recommended size range.

Clearing a Jam

If a fastener becomes jammed; before dissembling the gun;

DISCONNECT THE AIR SUPPLY.

Using the Allen Key provided undo the two caphead bolts that secure the front plate,

Remove the plates, clear the jam and replace the plates in the reverse order of removal.

Specification...

Axminster No.

Maximum Operating Pressure

Minimum Operating Pressure

Air Inlet

Air Consumption (constant usage)

Staple Gauge (20G)

Magazine Capacity

Maximum Staple Length

Minimum Staple Length

Staple Crown

Weight

Footprint (without PCL tail)

600515 (AW422J)

95 psi

60 psi

" BSP with standard PCL Fitting

3.8 CFM

1.2mm x 0.6mm (0.05" x 0.024")

100 Staples

22mm

6mm

11.2mm

1.3kgs

56mm wide x 200mm long x 180mm high

Identification and Description of the Stapler...

Main body

The main body is a casting that is extruded into the handle, the cylinder

housing, and the mounting points for the magazine assembly.

Connection port This is a

" BSP threaded hole which will allow you to mount the

connector of choice, to allow connection to the air supply.

Striker guide

Basically a shaped metal plate, that is bolted to the lower mounting of

body

the cylinder housing. It has a machined channel that guides the

striker/staple to the mouth when the stapler is fired.

Staple height

A flat metal plate secured to the front of the striker guide body by means

setting plate

of two panhead machine screws. The securing holes are elongated to

allow the plate to be moved up or down, so as to set the height of the

mouth above the work surface and thereby the driven height of the

staple. This is used when stapling something 'delicate' that could be

severed by just driving the staple home.

Magazine slide

A sprung loaded latch that locks the magazine slide closed. It is

latch

depressed to unlock the magazine slide to allow it to be withdrawn, to

facilitate the loading and unloading of the staples.

Magazine

The magazine assembly is also secured to the lower mounting of the

assembly

cylinder housing and supported at the rear underside of the handle. The

magazine basically consists of a 'U' shaped tray into which the staples

are laid, and the magazine slide plate, with a smaller inverted 'U' guide

fitted to it, which covers the fasteners, keeping them located in the tray.

Part of the slide plate mechanism is a sprung shoe that pushes against

the staples in the magazine tray and forces them into the receiver in the

guide body. The front end of the slide plate is the 'slipper' plate that

forms the rear part of the 'guide shute' down which the staples are fired.

The physical dimensions of the magazine assembly will limit the

maximum size of staples that can be inserted in the tool. There is no

such limitation on the minimum size, observe the figures in the

specification.

Trigger safety

This is a manual mechanical safety device above the trigger proper. It

Lock

locks the trigger off, so that a conscious action is required to 'unlatch'

the trigger to allow the tool to be used. This is because there is no

'contact safety enable' mechanism built into these tools.

Trigger

Provided it has been "unlatched", pressing the trigger will allow the gun

to fire the staple into the material.

Viewing

There are three peepholes in the magazine assembly to check whether

peepholes

there are staples loaded.

A X M I N S T E R

W H I T E