ABB ACS550 Series 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} ABB ACS550 Series에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ABB ACS550 Series 2 페이지. Drive it low voltage ac drives 150...550 hp
ABB ACS550 Series에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 사용자 설명서 (14 페이지), 설치 보충 설명서 (16 페이지)

페이지 인쇄

WARNING! To disconnect the internal EMC

filter, remove the screws marked with "

replace the screws marked with " " with the

provided polyamide screws, depending on

the frame size.

System type

R1...R3

R5...R6

EM1 EM3 EM1 EM3 F1 F2

IT system

Corner grounded TN

system

Power connections

See table Optional

Frame size R1...R4

braking below.

EM3

EM1

GND

X0033

Power input

Power output to motor

(U1, V1, W1)

(U2, V2, W2)

Frame size R5

See table Optional

braking below.

GND

X0035

Power input

Power output to motor

(U2, V2, W2)

(U1, V1, W1)

Frame size R6

See table Optional

braking below.

X0013

Power input

Power output to motor

GND

(U1, V1, W1)

(U2, V2, W2)

Optional braking

Frame size

Terminal labels

", or

R1, R2

BRK+, BRK-

Brake resistor

R3...R6

UDC+, UDC-

• Braking unit

• Chopper and resistor

Wiring the controls

1. Strip control cable

- -

sheathing and twist the

3, 4

copper shield into a

bundle.

2. Route control cable(s)

through clamp(s) and

tighten clamp(s).

3. Connect the ground

shield bundle for digital

and analog I/O cables at

X1-1. (Ground only at

the drive end.)

4. Strip the individual

control wires and connect to the drive terminals.

Use a tightening torque of 0.4 N·m (0.3 lb·ft). See

Control connections

below or, for more detail,

see User's Manual.

Control connections

ABB Standard macro

SCR

Signal cable shield (screen)

AI1

Ext. freq. ref. 1: 0...10 V

AGND

Analog input com.

10V

Ref. voltage 10 V DC

AI2

Not used

AGND

Analog input com.

AO1

Output freq.: 0...20 mA

AO2

Output current: 0...20 mA

AGND

Analog output com.

10 24V

Aux. volt. output +24 V DC

11 GND

Aux. volt. common

12 DCOM

Digital input com. for all

13 DI1

Start/Stop: Active = start

14 DI2

Fwd/Rev: Active = rev. dir.

15 DI3

Constant speed sel.

16 DI4

Constant speed sel.

17 DI5

Ramp pair: Active = 2

18 DI6

Not used

Relay output 1

19 RO1C

Default operation:

20 RO1A

Ready = 19/21 connected

21 RO1B

Relay output 2

22 RO2C

Default operation:

23 RO2A

Running = 22/24 connected

24 RO2B

Relay output 3

25 RO3C

Default operation:

26 RO3A

Fault(-1) =25/27 connected

27 RO3B

(Fault => 25/26 connected)

Note 1. Jumper setting (two switch types possible):

Note 2. Code: 0 = open, 1 = connected

DI3

DI4

Brake options

WARNING! The maximum voltage for digital

inputs is 30 V.

Check installation

Before applying power, perform the following

checks.

Environment conforms to specifications.

The drive is mounted securely.

IP5005

Proper cooling space around the drive.

Motor and driven equipment are ready for start.

For IT systems and corner grounded TN systems:

The internal EMC filter is disconnected (see the table

Wiring

power).

Drive is properly grounded.

Input power (mains) voltage matches the drive

nominal input voltage.

The input power (mains) terminals, U1, V1, W1, are

connected and tightened as specified.

The input power (mains) fuses are installed.

The motor terminals, U2, V2, W2, are connected and

tightened as specified.

Motor cable is routed away from other cables.

NO power factor compensation capacitors are in the

motor cable.

Control terminals are wired and tightened as

specified.

NO tools or foreign objects (such as drill shavings)

are inside the drive.

NO alternate power source for the motor is

connected – no input voltage is applied to the output

of the drive.

ramp pair

Reinstall the cover

1. Align the cover

and slide it on.

2. Tighten the captive

screws around the

edge of the cover.

3. Slide the hood

down over the top

of the cover (UL

type 12 only).

4. Install the two

AI1: 0...10 V

screws that attach

AI2: 0(4)...20 mA

the hood (UL type

12 only).

5. Install the control panel.

Output

Note: The control panel window must be closed to

Reference through AI1

1 (1202)

CONSTANT SPEED

2 (1203)

CONSTANT SPEED

6. Optional: Add a lock (not supplied) to secure

3 (1204)

CONSTANT SPEED

Apply power

Check

1. Apply input power.

Note: Before increasing motor speed, check that

Start-up

Assistant Control Panel

1. Use the MENU key to

2. Select ASSISTANTS.

3. Select Start-up Assistant.

4. Follow the screen

Note: For common parameters and menu items,

Basic Control Panel

comply with IP54 / UL type 12.

the control panel window.

Always reinstall the front cover before turning

power on.

WARNING! The ACS550 will start up

automatically at power up, if the external run

command is on.

When power is applied to the ACS550, the

green LED comes on.

the motor is running in the desired direction.

In start-up, enter motor data (collected earlier)

and, if needed, edit parameters that define how

the drive operates and communicates.

The Start-up Assistant steps through typical

start-up selections, and runs automatically

upon the initial power up. At other times, use

the steps below to run the Start-up Assistant.

access the Main menu.

LOC

49.1H

LOC

400RPM

1 Hz

1200 RPM

5 A

12.4 A

7 %

405 dm3/s

DIR

00:00

DIR

12:45

instructions to configure the

system.

use the Help key

to display

descriptions.

If you encounter alarms or faults,

use the Help key or refer to chapter

Diagnostics in User's Manual.

The Basic Control Panel does not

include the Start-up Assistant. Refer to

section How to start up the drive in

User's Manual and manually enter any

parameter changes desired.