CIOKS DC8 사용자 설명서 - 페이지 2

{카테고리_이름} CIOKS DC8에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. CIOKS DC8 2 페이지. Power supply for effect pedals

페이지 인쇄

Back

In the space on the back of the enclosure you'll find the AC power input socket, mains voltage

selector switch, fuse and the settings switch.

The AC power input socket is called C6 according to the IEC 60320 standard and it's the same

type used in many laptop power supplies.

Mains voltage selector switch should be used for setting the correct mains voltage 115 or

230V. The Japanese version is made only for a 100V nominal mains voltage and has no mains

voltage selector switch.

The fuse is the only part which can be replaced by the user. In case it's blown, replace with a

5x20mm, T315mA (slow blow/time lag) type.

The settings switch should be used for changing the operation settings of the power supply.

Bottom

The four detachable rubber feet are situated on the bottom of the enclosure. On this same

surface you'll find a table showing the different settings of the power supply, which you select

using the settings switch on the back. Also here are the 6 holes with metric M4 threads, which

should be used for easy mounting of the power supply to a pedalboard. Do not use screws,

which would go further than 5mm inside the unit. Have a look at the mounting guide on

CIOKS web site.

Getting started

First make sure that the voltage value chosen on the voltage selector switch matches the mains

voltage in your wall socket. Connect the mains power cord to the power supply and mains wall

outlet. Using the right Flex cable types connect your pedals to the outlets of power supply

making sure that the voltage and current is correct for every pedal. Rock'n'Roll..! ...or JaZz!

Settings

To change the settings of the power supply you use the settings switch on the back of the

enclosure. In the table below you can see the different settings:

No.

Function

Switch OFF (down)

Outlet 3

9V DC

Outlet 4

9V DC

Voltage settings

Voltage of outlets 3 and 4 can individually be set to 9 or 12V with switch knobs no. 1 and 2,

where the default value is 9V.

Features

Advanced LED Monitoring

Each isolated outlet or section has its individual LED status indicator. The indicator is lit in

normal operation. Its light gets dim when you operate just on the edge of the current limit. If

you overload or short circuit an outlet, the respective LED indicator turns off.

Switch ON (up)

12V DC

The LED indicators of outlets 3 and 4 with selectable output voltages 9 or 12V, also show you

the voltage chosen with the settings switch. In case a higher voltage than the default 9V setting

is selected for a given outlet, its respective LED indicator will be lit with higher intensity than

the other indicators. Default setting for outlets 3 and 4 is 9V and the higher value is 12V

All indicators take into account the actual level of mains voltage when monitoring a possible

overload. The current limits for each outlet or section of the power supply are specified at

nominal level of the mains voltage. In Europe it's 230V and 120V in e.g. United States. If the

mains voltage is higher than nominal, you can draw more current from the power supply than

stated in the specifications. This would never be a problem. A more common situation though,

is when the mains voltage is lower than nominal. In such a case maximum current ratings for

each outlet or section might be diminished.

The advanced LED monitoring of each isolated outlet will alert you in case of an overload or

short circuit. If such a situation happens you know where to look to solve the problem.

A glance at the LED status indicators and you have proof of 100% clean power to your pedals.

Included accessories

Flex cables

CIOKS offers a great selection of different Flex cable types for connecting your pedals to the

power supply. Below you see a list of the included Flex cables with your unit:

Type 1 – black with 5,5/2,1mm centre negative DC-plug

Type 2 – red with 5,5/2,1mm centre positive DC-plug

Type 4 – green with 5,5/2,5mm centre positive DC-plug

Type 5 – black with 3,5mm tip positive jack-plug

Type 6 – black with 9V battery clip

Split Flex type 1 – black with two 5,5/2,1mm centre negative DC-plugs

Stack Flex type 1 – black with 5,5/2,1mm centre negative DC-plug

Mounting hardware

We've included all the needed hardware to mount the power supply on top or underneath a

Pedaltrain or Temple Audio pedalboard. You can of course also attach it to boards of other

brands. Look on CIOKS web site for more information and mounting guides.

Not included accessories

More Flex cables and Booster Flex

To power one pedal using one outlet you simply use a single suitable standard Flex cable and

that's it. In case the plug type or length you need is not included with your unit there's a big

selection of standard Flex cables to choose from and order them separately. In case of an odd

voltage or current requirement you might need one of the Special Flex cables available. Please

read more about these and how to use them on CIOKS web site or in the included Flex guide.

They really open up for even more versatility and flexibility in terms of what you can power

with your unit.