Cipax RSK 6251190 설치 매뉴얼 - 페이지 3

{카테고리_이름} Cipax RSK 6251190에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cipax RSK 6251190 10 페이지.

페이지 인쇄

Installation manual

Closed Tank1350L/3000L/4000L/5000L/6000L

Edition 2022-01-17

1350L

CPX 23013

3000L

CPX 23020

3000L

CPX 23001

4000L

CPX 23031

5000L

CPX 23041

6000L

CPX 23060

General information

The CPX Closed Tank is rotation moulded in impact and age

resistant polyethylene plastic, intended for:

- Wastewater, both grey water (bath, shower and laundry) and

toilet/black water (economical flush version).

- Rainwater collection.

- Storage of drinking water. FC-approved product (Food Con-

tact).

The tank is not intended to be used as a septic tank.

The tank comes with a standard lockable lid, also rotationally

moulded in polyethylene plastic. The lid is tested and approved

by RISE (SP) according to the Boverket handbook on "Child-

proof wells" and SP method 0487 penetration test edition 3.

The tank can be installed both above and below ground.

Dimensions

Volume (L)

Art.no

LxWxH (mm)

1350

23013

1950x1200x1000 735

3000

23020

2350x1700x1350 1070

3000

23001

2350x2350x1000 770

4000

23031

2600x2350x910

5000

23041

2600x2350x1200 955

6000

23060

3400x2600x1175 1027

Before installation

A permit may be required for use as a sewage tank. Please con-

tact the Environmental & Health Protection Office (MHK) of the

relevant municipality before installation. Maximum allowed dis-

tance and suction height to sewerage emptying vehicles should

be investigated for the site before installation.

Equipment

The tank can be equipped with e.g. level alarm, enhancement

neck in different heights and rainwater kit for irrigation.

See

products.

Handling

The tank, equipment and accessories should be handled with

care. Keep away from objects that could damage them. On re-

ceipt and before installation, inspect the products carefully for

possible damage. The tank is delivered standing on an EU pallet.

Lifting the tank

The tank should be lifted with soft slings that can be threaded

through the moulded lifting loops. Only empty tanks may be

lifted and transported.

Safety

The lid is opened and closed with a tool, such as a 16 mm sock-

et wrench. The lid should always be in the locked position when

installed on the tank.

Gases can cause unconsciousness and immediate danger to life!

Pit

Choose a location where there will be sufficient slope (~2%

>~2cm/m) for drainage pipes and where the soil is considered to

be well drained and firm. Where there is a risk of groundwater

ingress into the pit, it is advantageous to provide drainage out of

the pit. The minimum size of the pit should be 500mm around

the tank. Leave sufficient space for the installation of pipes and

fittings.

The tank should not be located where there is a risk of it being

run over by, e.g, a car or similar. The groundwater level must

Inlet height (mm)

not rise to the inlet pipe. Avoid soil that is boggy or loose. Con-

sideration should also be given to the frost depth at the site.

Please document all or part of the installation with photographs

and sketched drawings for future reference.

Preparation of the pit

755

The tank should be placed on a well levelled and well drained

gravel or sand bed at least 150 mm thick, without sharp stones

or similar objects that could damage the tank. See table below

for maximum installation depth. If possible, compress the gravel/

sand bed with a soil compactor.

3/10

www.cipax.com

for more information on equipment and

Warning

Never enter a sewage tank that has been brought into use.