Arcam DAVE Amplifier 핸드북 - 페이지 3

{카테고리_이름} Arcam DAVE Amplifier에 대한 핸드북을 온라인으로 검색하거나 PDF를 다운로드하세요. Arcam DAVE Amplifier 14 페이지.

페이지 인쇄

Integrated amplifier - User Guide

Circled numbers in the text, e.g.

, refer to the numbers on the

pictures. If your integrated amplifier HAS NOT been installed for

you, you should read the section entitled 'Setting up' before using the

'User Guide'.

MODE

CONFIRM RECORD CONTROL

cn co cp cq

INTRODUCTION

A microprocessor is at the heart of the amplifier.

It performs several important functions. It switches the amplifier on

or off from standby mode and mutes the two sets of speakers

individually as well as the pre-amp output. It is also responsible for

the remote bus and infra red remote input. Parameters can be

selected, and displayed, on the built in graphic display enabling easy

set up of the amplifier and simple source selection. In addition, the

amplifier uses LED markers to indicate the primary source which is

in use. In addition to a full suite of audio line level inputs, there is

also a high quality optional MM/MC phono stage.To protect your

amplifier, the microprocessor monitors the heatsink temperature

and RF content of the speaker outputs. In the event of the amplifier

being over driven, it can activate the automatic speaker protection

circuits and it can report fault conditions to the main display.

IN USE

POWER

Switches the unit on and off.The unit can also be switched

into 'standby' by use of the remote control handset.

POWER INDICATOR

This will initially glow amber. After a few seconds, it will glow

green. When the indicator glows amber, the speakers are

disconnected and an internal protection circuit is activated.

The power indicator will turn red if the unit has been put

into standby mode by use of the remote control.

Under certain conditions the power indicator may flash and

a fault condition will be shown on the display

. If this

happens you should unplug the mains lead of the unit and

leave the unit for a few minutes before re-connecting.

If the fault condition persists unplug and contact your Arcam

dealer.

SP1

Selects or de-selects the main (upper) pair of speakers.

Push the button in to select.

SP2

Selects or de-selects the secondary (lower) pair of speakers.

Push the button in to select.

Important note: If both switches are turned off the amplifier

will appear not to work, as all speakers will be switched off!

A22 INTEGRATED AMPLIFIER

V V ol

olum

ume

2 TAPE 1

PHONO/AUX

TUNER

DVD

VCR

PROCESSOR

SP1

SP2

PHONES

POWER

dl dm dn

VOLUME

Adjusts the volume level of the loudspeakers, pre-amp out

and headphones.The volume can also be controlled with

the Remote Control Handset. As the volume knob is not

motorized the knob will not move when adjusted remotely.

If you spin the knob quickly it will not change the volume.

This is to prevent accidentally setting the volume too high.

NOTE ON VOLUME CONTROL SETTINGS

It is important to realise that the position of the volume

control is not an accurate indication of the power delivered

to your loudspeakers. The amplifier will often deliver its full

power long before the volume control reaches its maximum

position particularly when listening to heavily recorded

compact discs.

However the amplifier also has to be capable of giving full

power output from much lower level sources, such as tuners

and cassette decks. Using these sources, the volume control

setting may be much higher before distortion (audible

overload) sets in.

BALANCE

Press CONTROL

, turn the volume knob to the

desired balance, then press CONTROL again to fix the

balance you have selected.

CONTROL

This button cycles (or steps) through the functions that can

be controlled by the volume knob.This can be either

volume (the default setting) or balance. If you have a

DAVE or MARC, there are several other functions.

Refer to those sections of this handbook.

ENTERTAINMENT (SOURCE) SELECTORS

These buttons select the source (i.e. Radio (TUNER),

Compact Disc (CD) etc. you wish to listen to.

REMOTE RECEIVER

The remote receiver is behind the FMJ badge.

Make sure the remote receiver is not covered or signals

from the Remote Control Handset will not be received.

HEADPHONES SOCKET

Accepts headphones rated between 8 ohms and 2k ohms

fitted with a

" stereo jack plug. If you wish to listen on

headphones only, use SPl and SP2 (if necessary) to mute the

speakers.The headphone socket is always active.

Integrated amp - Using the Remote Control

If you have an integrated amplifier or MARC amplifier, you will have a Remote Control

similar to the one shown below.

This CR-389 Remote Control gives access to all functions available on the front panel

of FMJ amplifiers. It also has controls to operate Arcam CD players, AM/FM tuners

andDAB tuners.

The Remote Control transmits Philips RC-5 type codes.

TUNER

These buttons are used to control tuner

functions.

Note that the FM/DAB lights indicate into

which mode you are switching the remote

control.The lights only illuminate for five

seconds to conserve battery power.

If neither light is illuminated this does not

mean that the remote control is not

working!

OTHER AMPLIFIER FUNCTIONS

Note that greyed-out buttons on the

remote control diagram are of use with

other Arcam amplifiers.

SOURCE SELECTION BUTTONS

These operate in the same way as the

source selectors on the front panel of your

integrated amplifier.

Don't forget to fit the two AAA batteries

supplied and ensure they are inserted

correctly into the back of the remote

control before using it.

The Remote Control sends a message to an

infrared receiver which is located behind the

FMJ badge on the front of the amplifier.

Do not place anything in front of the badge

or the Remote Control may not work.

DAVE REMOTE CONTROL

If you have a DAVE amplifier, you will have the the CR9000

Remote Control as shown in the DAVE amplifier section

of this handbook.That Remote Control allows you to

operate the integrated amplifier plus some basic functions

of an Arcam or Philips based CD player or Tuner.

POWER/STANDBY

Toggles the amplifi er between standby

mode and full power mode.The power

indicator light next to the power button

on the front panel is red if the amplifier

is in standby, amber while the amplifier is

powering up (this only takes a few seconds)

and green when the amplifier is powered up.

SP1 AND SP2

These buttons allow you to select and

deselect the main(SP1) and secondary

(SP2) sets of speakers attached to your

amplifier (see page 4).

DISP

Cycles through the settings 'Bright', 'Off ' and

'Dim'.Turning the display 'Off ' generally

gives a slight improvement in sound quality.

VOLUME AND

(MUTE)

Press '+' to increase volume or '–' to

decrease the output volume of the amplifier.

Press '

' to mute the speaker connections

and preamp outputs. Both tape outputs and

the headphone socket remain active. Mute is

disabled either by pressing '

' again, or by

adjusting the volume.

CD CONTROLS

These offer basic controls of Arcam CD

players, such as the FMJ CD23.