Arcam FMJ A18 매뉴얼 - 페이지 10

{카테고리_이름} Arcam FMJ A18에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Arcam FMJ A18 14 페이지.

Arcam FMJ A18 매뉴얼

operation

Switching on

The front panel
button switches the unit on and
power
off.
The power light (next to the ' A 18 Integrated Amplifier'
text) indicates the state of the amplifier. The power LED
is green and ON if the power is connected and the unit
is turned ON.
display
The front panel
button (or
on the remote
dIspLAy
dIsp
control) changes the display brightness between 'on' ,
'dimmed' and 'off ' . If the A18 is powered off with the
display brightness set to 'off ' , the display resumes to
'dimmed' when the unit is powered on again.

Selecting an audio source

The audio source may be selected from the front panel
(
,
,
,
,
,
,
or
), or the
phono
AuX
cd
tuner
sAt
dVd
pVr
AV
remote control (
,
,
,
,
,
,
or
dVd
sAt
AV
tun
AuX
pVr
cd
In each case, the source is selected from the input
sockets with the corresponding name.
�������
����
������
����
�������
���������
����

listening

listening using speakers
Use the control knob to change the volume. Turn the
knob clockwise to increase the volume, anti-clockwise
to reduce it.
listening using headphones
The headphones socket (
) accepts headphones
phones
with an impedance rating between 8
and 2k
with a 3.5mm stereo jack plug.
The pre-amp outputs and speakers are muted when
headphones are plugged in. The headphones socket is
always active, unless output has been muted.
Muting output
The output of the A18 can be silenced by pressing
on the front panel (or
on the remote control). Press
-
-
for a second time (or change the volume) to
Mute/
cancel mute.
).
pho
AUX
�����
���
��
�����

adjusting listening settings

The A18 allows you to customise the balance, bass
and treble levels of the amplifier to fit your system.
Adjustments can be made either on the front panel or by
using the CR10 remote control. Click the corresponding
button to view the current setting, then use the control
knob on the front panel (or
/
VoL +
CR10) to adjust.
, fitted
balance
This setting allows you to increase the volume of one
channel (left or right) relative to the other. Altering
the balance (from L9 to R9, via the neutral value 0)
may help to restore the stereo image for an off-centre
listening position.
bass
Mute
This setting allows you to increase or decrease the level
of low frequency elements in the sound within the range
+7 to -7.
Treble
This setting allows you to increase or decrease the level
of high frequency elements in the sound within the
range +7 to -7.
direct mode
This is a 'tone defeat' setting which ignores any Bass and
Treble trim values.
Press
(Direct) on the remote control to toggle this
drct
setting; '
' is lit on the display when Direct mode
DIRECT
is active.
e-10
����
������������������������
31
������
���
���
���
��
���

Processor mode

The A18, in combination with a power amplifier, can
be used to drive the front left and right speakers of a
surround-sound system, when fed from a multi-channel
processor. The volume of the entire system may then be
controlled using the processor.
buttons on the
While in Processor mode, you can feed the sound from
the processor into
AV In
of the A18 to match the amplifiers that drive your
other loudspeakers. Set this 'Proc mode volume' using
the
and
buttons on the remote. The last set
VoL+
VoL–
value of 'Proc mode volume' is remembered whenever
Processor mode is selected.
Processor mode may be toggled on and off (when
is selected as the source) by using the front panel
AV
button or
processor Mode
remains lit on the display while Processor mode is
active.
������
�����
and set the 'Proc mode volume'
on the remote. 'PROC'
proc