Arcam FMJ A32 핸드북 - 페이지 6
{카테고리_이름} Arcam FMJ A32에 대한 핸드북을 온라인으로 검색하거나 PDF를 다운로드하세요. Arcam FMJ A32 16 페이지. Amplifiers
Arcam FMJ A32에 대해서도 마찬가지입니다: 서비스 매뉴얼 (18 페이지)
페이지 인쇄CONNECTING TO A POWER SUPPLY
WRONG PLUG?
Check that the plug supplied with the unit fits your supply and that
your mains supply voltage agrees with the voltage setting (115V or
230V) indicated on the rear panel of the unit
If your mains supply voltage or mains plug is different, consult your
Arcam dealer or Arcam Customer Support on +44 (0)1223 203203.
The product must be earthed.
MAINS LEAD
The appliance is normally supplied with a moulded mains plug already
fitted to the lead. If for any reason the plug needs to be removed, it
must be disposed of immediately and securely, as it is a potential shock
hazard when inserted into the mains socket. Should you require a new
mains lead, contact your Arcam dealer.
PLUGGING IN
Push the plug (IEC line socket) of the power cable supplied with the
unit into the socket (
POWER INLET
sure it is pushed in firmly.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
STANDBY POWER
For remote standby operation, the amplifier's control power supply
is kept powered up all the time the unit is connected to the mains
supply. The front panel power switch powers down all other circuitry.
Power consumption in this mode is less than 2W.
This means that even though the power switch is off, it may be possible
to hear a slight residual hum coming from the mains transformer inside
the amplifier. This is perfectly normal. If the unit is to be left unused for
an extended period, we recommend that it is disconnected from the
mains supply by switching it off at the wall socket.
CONNECTING TO OTHER EQUIPMENT
The use of high quality interconnect cables to and from your amplifier
is recommended to ensure the best sound quality. Sockets marked
(and
) on your amplifier should only be connected to sockets marked
R
(and
) on other equipment. All the line inputs have the same
L
R
sensitivity and may be used with equipment other than that labelled,
if needed.
8
TAPE1/RECORD OUT
the input sockets of your cassette deck (usually labelled
9
TAPE1/PLAY IN
– Connect these input sockets to the output
sockets of your cassette deck (usually labelled
a cassette deck you can use this input for other (line level) equipment,
such as a CD player, tuner, VCR, etc., but not a turntable.
VCR/TAPE2 RECORD OUT
be connected to the input sockets of VCR/second recorder (usually
labelled
).
RECORD
bl
VCR/TAPE2 PLAY IN
output sockets of your VCR/second recorder (usually labelled
Alternatively, you can use this input for other (line level) equipment
such as a CD player, tuner, etc., but not a turntable.
bm
DVD
– Connect this input to the audio outputs of a DVD
player.
2
before plugging in.
1
)
in the back of the unit. Make
– Connect these output sockets to
RECORD
). If you do not have
PLAY
bk
– These output sockets can
– Connect these input sockets to the
bn
AV
– Connect this input to audiovisual equipment such as a VCR,
laserdisc player, satellite or Nicam tuner.
bo
TUNER
– Connect this input to the audio outputs of your radio
tuner.
bp
CD
– Connect this input to the audio outputs of your CD player
or DAC (digital to analogue converter).
bq
AUX
– Connect this input to the audio outputs of any unit with
a line level output, e.g. tape deck, tuner etc.
bq
PHONO
turntable. This Phono Module is compatible with most high output
moving coil and moving magnet cartridges (MM) and low output
moving coil cartridges (MC). MM or MC can be selected via the blue
switch on the rear panel.
Phono earth terminal – For connecting your turntable earth lead
(if fitted). Note that this terminal must not be used as a safety earth.
TRIG OUT and REMOTE IN
connections are for use in multi-room installations. In normal use there
is no need to make any connections to these sockets. If you are
bi-amping with a power amplifier and wish to power both units on or
off simultaneously, see page 11.
PRE/POWER AMPLIFIER CONNECTIONS
5
– To use your integrated amplifier as a power amplifier,
PWR IN
connect the output of your pre-amplifier to the
Press in the
PRE/PWR
pre-amp/power amp mode. Under these circumstances your A32 has
exactly the same specification and performance as a power amplifier
(see page 8).
6
PRE OUT
connect the
PRE OUT
amplifier. With a power amplifier of the correct gain (e.g. the P35
L
power amplifier) you can bi-amplify ('bi-amp') suitable loudspeakers,
giving significant improvements in sound quality (see page 13).
).
).
PLAY
6
– Connect this input to the audio outputs of your
3
(12V in and out) – These
7
switch
on the rear panel to select separate
– To use your integrated amplifier as a pre-amplifier,
sockets to the input sockets of your power
sockets.
PWR IN