AXTON AXB20A 소유자 매뉴얼 - 페이지 3
{카테고리_이름} AXTON AXB20A에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AXTON AXB20A 11 페이지. 10"/25 cm active subwoofer
SAFETY INSTRUCTIONS
1. This unit is designed to be used in a vehicle with a 12V battery and negative ground.
2. Before any wiring, always remove the negative terminal of the battery to prevent short-
circuiting.
3. Do not disassemble or alter the unit in any way, because that will void your warranty. Do
not attempt to repair or to service the unit yourself, but contact an authorized AXTON
dealer instead.
4. Use only original accessories which are designed and manufactured for the unit,
otherwise you will risk damage. Install the unit according to the mounting manual and
use only the supplied mounting accessories. The forces of acceleration for accidents are
sometimes huge. Heavy objects may pose a risk for the driver and the passengers of the
car, during an accident.
5. Protect the unit from water and other liquids, which can enter the product. A short circuit
or even fire could result.
6. Before you replace a defective fuse, try to find the cause for the short circuit. Please
pay attention to the cables of the power supply! If the short circuit doesn't result from a
failure of the power supply or wiring, you can replace the defective fuse with a new one
of identical value. If the short-circuit still exists, please contact an authorized AXTON
dealer.
7. Be careful not to drain the car battery while using the unit when the engine is turned off.
Because the unit uses a considerable amount of energy and the battery will be charged
only while the engine is running, it might happen that the battery will discharge to a point,
where it's not longer possible to start the engine.
8. The amplifier module employs a protection circuit to protect the woofer from amplifier
malfunction. The amplifier's protection circuitry will shut-off the amplifier in case of short-
circuit, overload DC offset and in case of overheat. In case the cause for protection
shut-off has been eliminated, the amplifier will operate normally again (green LED ON).
Otherwise the amplifier will continue to remain in protection mode.
9. Do not use the unit with a weak or old battery as its optimum performance depends on
a normal battery supply voltage of 12V.
10. Please pay attention to the music playback volume inside your vehicle, because you are
obliged to notice exterior sounds like a police siren or you might face penalties in case
of an accident or even loose your insurance coverage.
11. Do not operate the unit in any other way than described in this manual. Failure to follow
the instructions within this manual will void your warranty.
– 4 –
WIRING & INTERFERENCE
All advice on wiring, controls and adjustments are based on the assumption that
n
you are thouroughly acquainted with all the requirements and features of the entire
audio equipment connected to this powered subwoofer!
All cables are sources of interference. The RCA audio cables are prone to interference
pick-up. There is often interference caused by the alternator (buzzing or whining), ignition
(crackling) or other car electronics. Most of these problems can be eliminated by correct wire
routing. In doing so, read the following guidelines first:
Use only double- or triple shielded RCA interconnects for the wiring between RCA input of
n
the amplifier and line-outs of the head unit.
Lay the signal and power cables separately with enough distance from one another and
n
also from other wire harnesses in the car. The REM cable to the amp remote output of the
radio can be laid together with the signal cables. Avoid ground loops by laying the ground
wiring of all components to a center point in a star-like way.
You can find the best central point in measuring the voltage directly at the battery. Compare
n
this voltage value with the chosen ground point and the (+) terminal of the amplifier. lf the
measured voltage offers less than 0.1 V difference you've found the correct central, which
should be clean and uncorroded.
– 5 –