Arcam DV88PLUS 핸드북 - 페이지 7

{카테고리_이름} Arcam DV88PLUS에 대한 핸드북을 온라인으로 검색하거나 PDF를 다운로드하세요. Arcam DV88PLUS 20 페이지. Arcam dvd player handbook

페이지 인쇄

Remote type

This informs the player which type of remote control you

are using, so that the player can take into account the slight

differences between the remote types. For ARCAM remote

controls, the remote type is always written on the front of the

remote control, normally at the bottom of the unit.

CR-314

This selects the grey ARCAM CR-314 remote

control

CR-80

This selects the black ARCAM CR-80 learning

remote control

CR-9000 This selects the black ARCAM CR-9000 learning

remote control

Other

A non-ARCAM learning remote control is being used

It is important to choose 'Other' if the learning remote in use

does not support RC-5 'toggle bits'.

OSD (On Screen Display)

This setting controls the 'pop up' messages that appear on

screen.

Pop-up messages are enabled

Off

No pop-up messages, only menus when required.

Certain messages, such as 'No Disc' are always shown

regardless of how this is set.

Video setup

Video 2/4

TV Shape

4:3 Letter Box

TV System

Progressive

HQ Video

RGB Scart

NTSC Black

7.5 IRE(Standard)

TV shape

This needs to be set correctly for the type of TV you have and

the type of display you prefer.

4:3 Letterbox Use this setting if you have a conventional 4:3

TV, and you prefer to view wide screen movies

in letterbox format (with black bars at the top

and bottom)

4:3 Panscan Use this setting if you have a conventional 4:3

TV, and you prefer to view wide screen movies

in Pan & Scan format (cropping the sides of the

image)

16:9

Use this setting if you have a wide screen (16:

9) TV. Material in 16:9 format is displayed so

as to fill the screen.

If you have a 4:3 TV and you have set a preference for Panscan,

it does not mean you will always see movies in this format,

since the Panscan display must be supported on that disc.

TV System

This is set at the factory to be appropriate for the type of TV

used in your country. Should you need to change this setting,

the options are explained below.

Auto

The video output is taken from that recorded on

the disc. When no disc is playing, the logo screen

is displayed using the standard of the last disc

played.

NTSC

NTSC is always used as the video standard. Note

that PAL discs are converted to NTSC, but this

causes some reduction in the quality of the video

Auto

Off

output (and may cause the video to become

'jerky'). This is the best setting to use if your TV

can accept only NTSC video (this is generally the

case in North America); better results are obtained

by using 'Auto', but your TV must be able to

support PAL.

PAL

PAL is always used as the video standard. Note

that NTSC discs are converted to PAL, but this

causes some reduction in the quality of the video

output (and may cause the video to become

'jerky'). Better results will be obtained by using

'Auto', but your TV must be able to support NTSC.

Progressive

Off

The video output will always be interlaced (standard

definition video). Use this setting if your display

device does not support progressive scan.

Auto

The component video output will switch to

progressive scan mode whenever the output

standard is NTSC (525). This would be whenever

an NTSC disc is played, or whenever 'TV System'

is set to NTSC. The video output will revert to

interlaced (standard definition) for PAL (625)

modes. Use this setting only if your display device

supports progressive scan.

NOTE: When progressive scan is active, the component

video output will be in progressive mode, and the other video

outputs (composite and S-Video) are muted.

Since progressive scan must be component, not RGB, the

'HQ video setting' will be forced to component if progressive

scan is enabled.

Not all displays support progressive scan. If you accidentally

enable progressive scan and your display does not support

it, you will be unable to view the picture from the DVD player,

including the on screen display required to change the video

settings. To revert to interlaced mode without using the on

screen menus, press and hold the

panel at any time. The video mode will revert to interlaced

mode after the button has been held in for five seconds.

HQ Video (High Quality Video)

This setting controls the type of video given out on the

Component and SCART video outputs. It is set at the factory to

be appropriate for the type of TV used in your country, so it is

best not to change it. If it gets set incorrectly then the picture

shown on the TV will have strange colouring.

Component

The video output on both the Component video (3

phonos) and SCART is Y, Pb, Pr component video.

RGB SCART

The video output on both the Component video (3

phonos) and SCART is RGB. Note that if you are

using RGB output via phono connectors, you will

also need to use

COMPOSITE

NTSC black (Pedestal)

This setting controls the 'pedestal' signal or black level when the

NTSC video standard is used. Note that it does not affect PAL

video in any way.

0 IRE

This removes the pedestal from NTSC video. This

setting should be used in Japan, and also if you are

using RGB video, whatever the country.

7.5 IRE This is the standard pedestal level that should be

used in all countries that use NTSC video, with the

exception of Japan.

button on the front

STOP

as a sync signal.

DV88

PLUS