3Com CoreBuilder 5000 빠른 시작 및 참조 - 페이지 4

{카테고리_이름} 3Com CoreBuilder 5000에 대한 빠른 시작 및 참조을 온라인으로 검색하거나 PDF를 다운로드하세요. 3Com CoreBuilder 5000 17 페이지. 3com computer accessories user manual

페이지 인쇄

UILDER ®

5000 S

ORE

IEC 825, Class 1 LED Device. For connection only to

Class 1 LED Devices.

CLASS 1

LED PRODUCT

6.0

Unpacking Procedure

Follow this procedure to unpack a SwitchModule:

1 Verify that the SwitchModule is the model that you

ordered by examining the model number on the side of

the shipping carton.

2 Remove the SwitchModule, in its antistatic bag, from

the shipping carton.

3 Following the instructions in Section 5.0, "Installation

Precautions", remove the SwitchModule from the

antistatic bag and inspect it for damage.

If the SwitchModule appears to be damaged, return it

to the antistatic bag, repack it in the shipping carton,

and contact your local supplier.

Keep the shipping carton and antistatic bag in which

your SwitchModule was shipped for future storage or

shipment.

4 Record the serial number of your SwitchModule. Use

the CoreBuilder 5000 SwitchModule Planning Chart

that comes with this product.

5 Ensure that the CoreBuilder 5000 SwitchModule Kit

contains these items:

CoreBuilder 5000 SwitchModule

Release Note for CoreBuilder 5000 SwitchModules

3Com DocsOnCD documentation CD-ROM (contains

CoreBuilder 5000 SwitchModule User Guide)

CoreBuilder 5000 SwitchModule Quick Start and

Reference (this guide)

CoreBuilder 5000 SwitchModule Command Reference

CoreBuilder 5000 SwitchModule Planning Chart

WITCH

ODULE

UICK

TART AND

EFERENCE

7.0

Installing the SwitchModule

You do not need to turn off the CoreBuilder 5000 hub to

install or remove the SwitchModule. You can install the

SwitchModule while the hub is operating (which is called a

hot swap).

Before you start the installation process, read

Section 3.3, "Software Prerequisites," and Section

5.0, "Installation Precautions".

To install a SwitchModule:

1 Determine hub power. To ensure that the hub has

enough power to support the new SwitchModule:

a Enter the SHOW POWER BUDGET command to see if

sufficient wattage is available from the +5 volt,

–5 volt, and +12 volt supplies.

b Using the values in the following table, add up the

total power requirements for the SwitchModules that

you plan to install:

Model Number

3C96618M-TX-A

3c96620M-TP-A

3C96612M-TP-A

3C96624M-TP-A

3C96624M-TPL-A

3C96616M-BTP-A

3C96610M-F-A

3C96620M-F-A

3C96614M-FTP-A

3C96612M-FF-A

3C96604M-F-A

3C96612M-FC-A

3C96604M-TX-A

3C96604M-FX-A

Power Requirement at

+5 Volts

–5 Volts

+12 Volts

52 W

0.5 W

0.25 Watts

for all

25 W

0.5 W

modules

23 W

0.5 W

30 W

0.5 W

25 W

0.5 W

35 W

1.0 W

33 W

0.5 W

50 W

0.5 W

30 W

0.5 W

40 W

0.5 W

31 W

0.5 W

57 W

0.5 W

34 W

0.5 W

35 W

0.5 W