Arcam SOLO MINI 핸드북 - 페이지 6

{카테고리_이름} Arcam SOLO MINI에 대한 핸드북을 온라인으로 검색하거나 PDF를 다운로드하세요. Arcam SOLO MINI 18 페이지. Music system
Arcam SOLO MINI에 대해서도 마찬가지입니다: 브로셔 (2 페이지), 핸드북 (20 페이지)

페이지 인쇄

rear panel

Analogue inputs

Solo Mini provides four pairs of analogue

inputs, allowing connection of other stereo

sources (e.g. a games console, AV, iPod/

Tape, or TV). All four inputs have the same

characteristics – the labels below the inputs

give suggested uses.

To connect a device to an input on the

rear of Solo Mini, use a stereo phono cable

of a suitable length. We advise you to use

high-quality interconnect cables wherever

poss ble to ensure the best poss ble sound

quality.

RS232 control

This is used for controlling an iPod (see page 9),

or for control via a remote computer.

Antennae inputs

These inputs can be used with the aerials

provided (DAB, if fitted, has a telescopic

aerial, FM a wire aerial, and AM a loop

aerial). In weak signal areas, external aerials

of the correct type may be required for

optimal reception.

RS232 CONTROL

DAB

GAME

iPod/TAPE

TAPE

PRE OUT

OUT

Tape output

This is the output to be used

for connecting to an audio

recorder or for a second room

system. It should be connected

by Phono–Phono (RCA)

cables to the amplifier in the

second room.

Preamp output

If you require more power than Solo Mini's 25W per

channel, you can connect an external power amplifier.

Connect the

sockets to the input sockets of

PRE OUT

your power amplifier, then connect your speakers to

the power amplifier's speaker terminals.

This output may also be used to provide a signal for

a self-powered Low Frequency Effects speaker (a

subwoofer). Arcam's Logo speaker ideally matches

the design and output characteristics of Solo Mini.

Speaker outputs

Connect your Muso speakers

here!

RIGHT

LEFT

SPEAKER

OUTPUT

–

220-240V

50–60Hz

250W MAX

REMOTE

PROG

OUT

OFF/ON

Programmer switch

This is an override switch that allows an

Arcam dealer to install software upgrades.

The user should not access this facility.

Remote output

This output carries all signals from the

front-panel remote-control receiver. This

can be used to route remote-control

commands to other equipment (potentially

in different locations). For example,

amplifier commands could be received by

Solo Mini, then routed to a power amplifier

in a remote location using this output

connector.

Controlling an iPod

Music or podcasts from your iPod can

be fully integrated with your system

using Arcam's rDock or rLead. These

accessory units use the

RS232 CONTROL

and

connectors to take over

IPOD/TAPE

the control and amplification, with

iPod text appearing on the front panel

display of Solo Mini.

Information on connecting and using

an iPod with the Solo remote is given

in the rDock or rLead quick start

guide supplied with these accessory

units, but see 'iPod connection' in the

connectivity section of this manual.

Mains power input

100V, 115V or 230V AC,

depending on shipping region

Mains switch

This is the main Off/On

switch, though it is usual to

place the unit in low-power

'Standby mode' when not

in use.

Connecting a record deck

Solo Mini is not fitted with a phono

pre-amplifier. If you wish to connect

a record deck to Solo Mini, then

you'll need an external pre-amplifier.

Please contact your dealer for further

information and recommendations on

the best option for you.