Axxess AXDIS-BW122 설치 지침 - 페이지 3

{카테고리_이름} Axxess AXDIS-BW122에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Axxess AXDIS-BW122 4 페이지. Bmw (with m.o.s.t. 25 amplifier) 2004-2013

페이지 인쇄

INSTALLATION

With the key in the off position:

• Connect the AXDIS-BW122 harness to the AXDIS-BW122 interface.

• Connect the AXDIS-BW122 harness to the AXDIS-BW122 amplifier interface.

• Remove the dust cover from fiber optic port in the AXDIS-BW122 amplifier interface.

• Connect the factory fiber optic cable into the AXDIS-BW122 amplifier interface.

• Connect the AXDIS-BW122 harness to the wiring harness in the vehicle.

• Connect the AXSWC harness to the AXSWC interface, and then to the AXDIS-BW122 interface.

PROGRAMMING

• Press and hold the Volume-Up button on the steering wheel.

• Turn the ignition on, the L.E.D. in the AXSWC interface will start flashing rapidly, which

means the AXSWC is looking for the vehicle and the radio.

Note: If the L.E.D. did not start flashing rapidly, press the reset button for 3 seconds, while still

holding the Volume-Up button.

• After a few seconds the L.E.D. should stop flashing rapidly, and then go out for

approximately 2 seconds.

• After approximately 2 seconds there will be a series of 7 Green flashes, some short, and

some long. The long flashes represent the wires that are connected to the AXSWC. The 3rd,

4th, 5th, and 6th flashes should be longer.

Tip: Knowing this will help to troubleshoot, if need be.

• The L.E.D. will pause for another 2 seconds, and then flash Red up to 18 times depending on

which radio is connected to the AXSWC. Refer to the L.E.D. feedback section for information.

• This is the end of the auto detection stage. Release from holding the Volume-Up button.

If the AXSWC detected the vehicle and the radio successfully, the L.E.D. will light up solid.

• Test the steering wheel controls for proper operation. Refer to the AXSWC instructions online at

axxessinterfaces.com for customizing the buttons, if so desired.

PROGRAMMING

L.E.D. feedback

The (18) Red L.E.D. flashes represent which brand radio the AXSWC is connected to. Each

flash represents a different radio manufacturer. For example, if you are installing a JVC radio,

the AXSWC will flash Red (5) times, and then stop. Following is a legend that dictates which

radio manufacturer corresponds to which flash.

L.E.D. feedback legend

1 flash - Eclipse (Type 1) †

2 flashes - Kenwood ‡

3 flashes - Clarion (Type 1) †

4 flashes - Sony / Dual

5 flashes - JVC

6 flashes - Pioneer / Jensen

7 flashes - Alpine *

8 flashes - Visteon

9 flashes - Valor

* Note: If the AXSWC flashes Red (7) times, and you do not have an Alpine radio connected to

it, that means the AXSWC does not detect a radio connected it. Verify that the 3.5mm jack is

connected to the correct steering wheel jack/wire in the radio.

** Note: The AXSWCH-PAR is required (sold separately). Also, the Parrot radio must be updated

to rev. 2.1.4 or higher through www.parrot.com.

† Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio type to

the other Clarion radio type; same for Eclipse. Refer to the "Programming Information" document online.

‡ Note: If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC radio,

change the radio type to a Kenwood. Refer to the "Programming Information" document online.

(CONT.)

10 flashes - Clarion (Type 2) †

11 flashes - Metra OE

12 flashes - Eclipse (Type 2) †

13 flashes - LG

14 flashes - Parrot **

15 flashes - XITE

16 flashes - Philips

17 flashes - TBD

18 flashes - JBL

REV. 11/13/2019 INSTAXDIS-BW122