Creda ADVANTAGE 550 설치 및 사용자 설명서 - 페이지 6

{카테고리_이름} Creda ADVANTAGE 550에 대한 설치 및 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Creda ADVANTAGE 550 6 페이지. Electric shower

페이지 인쇄

c) ELECTRICAL

WARNING: THIS SHOWER MUST BE EARTHED.

The electrical installation must be in accordance with the current BS.7671 (IEE Wiring Regulations)

and "Part P" of the Building Regulations and/or local regulations.

1. The shower unit is designed for a single phase AC electrical supply.

Please check the rating plate on the unit to see what details apply to your shower.

AS A GUIDE ONLY

(* Only applies if external earth impedance is less than 0.35 Ohms)

Rating

Cable Sizes

6.0mm²

10.0mm²

8.5 / 7.8kW 240 / 230V

6.0mm²

10.0mm²

6.0mm²

10.0mm²

9.5 / 8.7kW 240 / 230V

6.0mm²

10.0mm²

10.5 / 9.6kW 240 / 230V

10.0mm²

Remember to upgrade the cable if it runs in thermal insulation in a loft, or for a longer distance.

2. A means for disconnection in all poles must be incorporated in the fixed wiring in accordance with

the wiring rules. We recommend a ceiling switch mounted in a convenient position.

3. If you have decided to connect the cable on the left hand side then please remove and use the

cable clamp that was provided along the right side (see Diagram 3a/b).

WARNING: IF LEFT HAND SIDE CABLE ENTRY IS USED, THE MAINS CABLE OUTER SHEATH

MUST BE STRIPPED BACK TO THE LEVEL MARKED ON THE BACKPLATE, AND ALL

THREE CONDUCTORS MUST BE FULLY SLEEVED WITH THE SLEEVING PROVIDED

BETWEEN THERE AND THE TERMINAL BLOCK (SEE DIAGRAM 3a).

4. Connect cable to terminal block making sure that all the retaining screws are VERY

TIGHT and that no cable insulation is trapped under the screws.

WARNING: FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD

RESULT IN FAILURE OF THE TERMINAL BLOCK.

5. Re-fit the detachable bottom section with the two screws if it was removed.

IMPORTANT: Ensure you connect the flying lead from PCB to the front cover.

6. Re-fit the front cover, and secure by replacing the top and bottom fastening screws.

Fuse / MCB

Cable Length

27m Max.

40A Type B MCB

45m Max.

12m Max.*

45A BS.1361 fuse

21m Max.*

27m Max.

40A Type B MCB

45m Max.

12m Max.*

45A BS.1361 fuse

21m Max.*

45A BS.1361 fuse

12m Max.*

7. Fit the shower hose, and operate the shower first without the handset to flush out particles,

fit the handset and then operate the shower as on page 8 or 12 and check:

Water gets to a satisfactory temperature and water flow can be adjusted by control knob "E".

Knob "E" has been correctly engaged by ensuring that the knob turns approximately one full turn.

Power selection operates in all 3 button settings, giving a change in water temperature.

Check again for leaks and that the holes in the shower handset are not blocked.

8. Demonstrate the showers operation to all users.

ASSEMBLY OF ACCESSORIES

Diagram 4 (Riser Rail and Soap-Dish Fitting Instructions)

(Refer to the separate fitting instruction sheet packed with the accessories for more details)

1. Establish height of riser rail to suit user requirements.

This should be a maximum of 0.6 metres (2ft)

above the level of the heater, see (a) and Diagram 1.

2. Remove covers from the wall brackets (b).

3. Hold the rail assembly in the selected position against

the wall, ensure that the brackets are vertically aligned,

and mark the wall for upper and lower screw fixings (c).

NOTE: The adjustable slider grips the conical nut on the shower hose (e).

HOW TO MAINTAIN YOUR JETSPA SHOWER

It is recommended that the shower unit and hose etc. be cleaned using a soft cloth and that the use of

abrasive or solvent based cleaning fluid be avoided, especially on any plated finishes.

We recommend that before any cleaning, the isolating switch be turned off, thus avoiding accidentally

switching on the shower.

WARNING: YOU MUST REGULARLY INSPECT THE SHOWER HOSE FOR WEAR

AND DAMAGE. REPLACE IF NECESSARY, OR EVERY TWO YEARS,

WITH AN APPROVED PART.

WARNING: IN ORDER TO MAINTAIN THE PERFORMANCE OF YOUR SHOWER,

YOU MUST REGULARLY CLEAN THE SHOWER HANDSET.

All water contains particles of lime-scale, which build up in the shower handset and

unit reducing the performance.

It is therefore important to clean the shower handset by simply rubbing the rubber

nozzles, or soaking in proprietary lime-scale remover and rinsing thoroughly before use.

NOTE: After use it is normal for some water to drip from the shower handset for a

few moments. This inhibits lime-scale build-up over prolonged use.

ADDITIONAL ACCESSORIES

Please Note:- The fitting of Spare Parts must be supervised by a suitably qualified person.

WRAS Listed Water

Isolating Valve

Cat No. 93792452

Curtain and Rail Pack

Cat No. 83792812

A more comprehensive list of additional accessories and spare parts can be supplied

against any Credit or Debit cards from Creda Sales Hotline 0870 9000 420

4. Drill and plug the wall.

5. Remove lower bracket from the rail and fit the

adjustable slider, hose-retaining ring and

soap dish onto the rail (d).

6. Replace the lower bracket and fix the

assembly to the wall.

7. Replace the covers onto both brackets.

COMMON SPARE PARTS

Front Cover without PCB

Cat No. 93590383

Front Cover complete with PCB

Cat No. 93590384

Thermal Cut-Out 50/88°C

Cat No. 93597871

Solenoid Valve

Cat No. 93590355