Creda JETSPA CONTEMPORARY 설치 및 사용자 설명서 - 페이지 5

{카테고리_이름} Creda JETSPA CONTEMPORARY에 대한 설치 및 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Creda JETSPA CONTEMPORARY 6 페이지. Electric shower

페이지 인쇄

HOW TO USE YOUR JETSPA SHOWER (DETAILED)

1. Ensure the electricity and water are turned on to the unit.

2. Your shower can be turned on by pressing either

Button "A", Button "B" or Button "C" (see Diagram 5).

Button "A" (III) - Starts shower on "High" power.

Button "B" (II) - Starts shower on "Medium" power.

Button "C" (I) - Starts shower on "Cold".

Once pressed, a light will illuminate above the button

confirming that power selection has been made.

Knob "E" controls the temperature of the water, and

For this example turn Knob "E" to "mid-position".

3. Press Button "A" and the water will flow.

4. Allow about 20 seconds for the temperature of the water to stabilise.

It is recommended that you do not wholly enter the water spray

during this period, even if the shower has just been used.

IF WATER IS TOO COLD

Turn Knob "E" anti-clockwise "1/8" of a

turn, and continue turning anti-clockwise until

you get the water temperature of your liking.

Wait 20 seconds after each adjustment for

the water temperature to stabilise.

The final adjustment may be in any position.

If after turning fully anti-clockwise water is

still too cold, set shower pattern on shower

handset to outer or inner pattern only.

5. Once a temperature setting to your liking has been achieved, Knob "E" will rarely need adjusting.

You must however take into account required adjustments for variations of incoming mains water

temperature between summer and winter (see "Effect of Seasonal Incoming Water Temperature

Changes" page 10).

6. When you have finished showering, press button "D" ( ) only, the LED light above will flash.

Water will continue to flow for up to 7 seconds before switching off.

Wait for the water to stop, and then switch off the electricity at the ceiling switch or local isolator.

7. Turning the shower on by pressing Button "B" reduces the power used by the shower giving a

cooler shower or the option of reduced water flow.

This option is mainly for summer usage and if this is used then Knob "E" must be re-adjusted.

Turning the shower on by pressing Button "C" will supply water without any heating

9. Your shower is designed to stabilise temperature changes caused by water pressure fluctuations

(see "Effect of Other Water Devices on Incoming Water Supply" see page 10).

WARNING: DO NOT SWITCH THE SHOWER ON IF YOU SUSPECT IT OF BEING FROZEN.

WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.

WARNING: DO NOT OPERATE THE SHOWER IF WATER IS DISCHARGED FROM THE

PRESSURE RELIEF VALVE. MAINTENANCE IS REQUIRED BEFORE THE SHOWER

CAN BE SAFELY USED

WARNING: CONSIDERATION SHOULD BE GIVEN TO SUPERVISING THE YOUNG, ELDERLY

AND THE INFIRM WHILST THEY USE THIS SHOWER.

IF WATER IS TOO HOT

Turn Knob "E" clockwise "1/8" of a turn, and

continue turning clockwise until you get the water

temperature of your liking.

Wait 20 seconds after each adjustment for the

water temperature to stabilise.

The final adjustment may be in any position.

If after turning fully clockwise, water is still too hot,

press Button "B" (II - medium) and re-adjust Knob

"E" to give desired temperature.

Water flow will be reduced on this setting.

COLD WATER INLET PIPE CONFIGURATION

Please note that standard compression fittings are shown.

Push-Fit connections or a combination of the two are also suitable.

To aid installation, you may find it convenient to move the flexible pressure relief valve outlet

assembly by removing the two securing screws.

If you do, please ensure that they are fully tightened on re-assembly (see Diagram 2b).