Epson C11C524025 - FX 890 - Printer 제품 정보 매뉴얼 - 페이지 3

{카테고리_이름} Epson C11C524025 - FX 890 - Printer에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson C11C524025 - FX 890 - Printer 19 페이지. Impact printers
Epson C11C524025 - FX 890 - Printer에 대해서도 마찬가지입니다: 사용자 설명서 (48 페이지), 매뉴얼 (11 페이지), 사양 (2 페이지), 기술 요약 (7 페이지)

Epson C11C524025 - FX 890 - Printer 제품 정보 매뉴얼
EPSON FX-890/FX-2190
Roll paper holder (8310)
Allows you to use your printer with 8.5-inch roll paper.
Front sheet guide (C814001 for FX-890,
C814011 for FX-2190)
Allows you to load single sheets and carbonless single-sheet
multi-part forms of up to 6 parts.
Front paper guide (C814021 for FX-890,
C814031 for FX-2190)
Allows you to load single sheets and carbonless single-sheet
multi-part forms of up to 6 parts without removing the
tractor from the front push position.
Optional Interface Cards
You can install an optional interface card to supplement your
printer's built-in USB and parallel interfaces and provide added
network compatibility. The EPSON interface cards in the table
below are compatible with your printer.
Card type
Serial interface
32 KB intelligent serial interface
Coax interface
Twinax interface
IEEE-1284 parallel interface
EpsonNet 10/100 Base TX Internal Print Server
Note: Other network interface cards (such as the C823622A,
C823632A, and C823642A) are also supported on this printer. Check
with EPSON for more information.
2 - EPSON FX-890/FX-2190

Printer Specifications

Mechanical
Printing method
Printing speed
Printing direction
Model number
C823051
C823071
Line spacing
C823141
C823151
Printable columns
C823452
C12C823912
Resolution
Paper feed
methods
Paper feed speed
6/03
9-pin impact dot matrix
Ultra speed draft
566 cps at 10 cpi
680 cps at 12 cpi
High-speed draft
559 cps at 10 cpi
627 cps at 12 cpi
Draft
419 cps at 10 cpi
503 cps at 12 cpi
Near letter quality
104 cps at 10 cpi
125 cps at 12 cpi
Bidirectional logic seeking for text and
graphics printing. Unidirectional text or
graphics printing can be selected using
software commands.
1/6-inch or programmable in
1/432-inch increments
FX-890: 80 columns (at 10 cpi)
FX-2190: 136 columns (at 10 cpi)
240
144 dpi (near letter quality)
Friction (front, rear)
Push tractor (front, rear)
Pull tractor (front, bottom, rear)
Push and pull tractor (front, rear);
additional tractor is required
Cut-sheet feeders (optional)
Roll paper holder (optional)
Normal mode:
1/6-inch (4.23 mm) feed, 62 msec;
Continuous: 5 inches (127 mm)/
second
Copy mode:
1/6-inch (4.23 mm) feed, 83 msec;
Continuous: 3.1 inches (78 mm)/
second;