Epson DFX-8500 - Impact Printer 제품 정보 - 페이지 8

{카테고리_이름} Epson DFX-8500 - Impact Printer에 대한 제품 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson DFX-8500 - Impact Printer 15 페이지. Warranty statement
Epson DFX-8500 - Impact Printer에 대해서도 마찬가지입니다: 브로셔 및 사양 (24 페이지), 사양 (2 페이지), 제한 보증 (2 페이지)

페이지 인쇄

EPSON DFX-8500

Adjusting the top-of-form position

The top-of-form position is the position to which the printer

feeds the paper when it loads it or performs a form feed. This

position is important because it determines where the printing

begins on each page. If the printing is too high or low on the

page, you can adjust the top-of-form position either

permanently or temporarily depending on how you use the

button.

TOF

When you want to permanently change the top-of-form

position, you enter the top-of-form mode using the

control panel button. The printer remembers the new top-

of-form position even after the printer is turned off, reset, or

initialized. (The printer remembers separate top-of-form

positions for the front and rear tractors.)

When you want to temporarily change the top-of-form

position, you adjust the position using the

buttons during pause status without entering top-of-form

mode. The printer remembers the temporary top-of-form

position until the next time you load paper, switch tractors,

or turn off the printer.

You can set the top-of-form position from 2.6 mm (0.1 inch)

to 33.9 mm (1.33 inch) below the top edge of the paper. The

factory setting is 5.8 mm (0.2 inch).

Follow the steps below to reset (permanently change) the top-

of-form position.

CAUTION:

To adjust the top-of-form position when labels are loaded in the

printer, use the forward-feeding (top) Micro Feed button only;

do not enter the top-of-form mode. Never feed labels backward

through the printer.

1. Make sure the printer is turned on and the desired tractor is

selected (the corresponding tractor arrow should be lit).

2. Open the top cover.

3. Press the

button to enter top-of-form mode. The

TOF

printer beeps once, and the

printer advances the paper so that the top-of-form position

is lined up with the red line on the clear plastic ribbon

protector.

4. Use the

buttons to feed the paper to the desired

Micro Feed

top-of-form position. The red line on the ribbon protector

shows you where the bottom edge of your first line of text

will print. This position is based on the first printable line of

8 - EPSON DFX-8500

TOF

Micro Feed

light flashes. Also, the

TOF

text. If your software inserts a top margin of five lines, your

text will actually print five lines below the top-of-form

position.

Note:

The red line on the ribbon protector can be used as a reference

only when you are in top-of-form mode. At all other times your

top-of-form position is hidden behind the print ribbon.

5. Press the

button again to exit and save your new top-

TOF

of-form position. Then close the top cover.

Note:

If you enter top-of-form mode right after loading paper, you can

set the loading and top-of-form positions at the same time.

(When you use the optional pull tractor, you cannot adjust the

loading position.)

Adjusting the printing position

You may need to adjust the printing position in the middle of

a page, or to adjust the top-of-form position when using

labels.

When you move the printing position, you temporarily

change the top-of-form position by the same amount. For

example, if you adjust the printing in the middle of the page

so that it falls a half-inch lower, the next page will begin

printing a half-inch lower as well. The printer remembers this

temporary top-of-form position until the next time you load

paper, switch tractors, or turn off the printer. To adjust the

printing position or top-of-form position, follow these steps:

1. Start printing your document. When you reach the text that

you want to align at a particular spot on the page, press the

button to stop printing.

Pause

2. Use the

Micro Feed

you want your next line of text to fall. Press the button once

to feed the paper forward or backward in 1/216-inch

increments, or hold it down to move the paper

continuously.

CAUTION:

If you are printing on labels, continuous forms with labels, or

overlapping multi-part forms, use only the forward-feeding (top)

Micro Feed button.

3. When you are finished, press the

printing your document.

5/98

buttons to adjust the position where

button to resume

Pause