ARCHIPELAGO LIGHTING LED SL-7.5 설치 지침 - 페이지 2
{카테고리_이름} ARCHIPELAGO LIGHTING LED SL-7.5에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. ARCHIPELAGO LIGHTING LED SL-7.5 4 페이지. Led shop/utility light
페이지 인쇄Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with package contents list on previous page. If any part is
missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts. Select suitable location that can support
the weight of the fixture. Determine method of mounting before drilling. Mark two spots on the ceiling 44-1/2 in. apart for the mounting hardware .
1
Mounting to drywall
Drill a ¼ in. hole in the ceiling to clear
the closed flaps of the toggle bolt.
Make sure to fasten the
toggle bolt into the butterfly nut before
inserting the flaps into the ceiling.
Tighten the toggle bolt.
5
Connecting the power
cord
After installation, plug the power cord (B)
into the power supply.Pull to turn on the
Switch (C).
WARNING: "J" Hooks are for mounting onto wood ceiling or a plaster board surface(Recommend
!
minimum 3/8" thick). Install each "J" hook ( ) or other mounting/hook option exactly 35.5 inches apart.
Check to make sure the hold is secure and appropriate for the weight of the shop light. Never hang
on the shop light or hang any object from the shop light.
WARNING: DO NOT INSTALL on radiant-heating ceilings.
!
WARNING: These hooks are to engage the hanging chain only and not the electric cord.
!
Optional Surface Mounting
1
Securing fixture to ceiling
Once the head of the screw is in beyond the opening gently slide the fixture
to the right or left to secure it in place
You may need to adjust the depth of both screws to get a tight fit
Care & Cleaning
CAUTION: Before attempting to clean the fixture,
disconnect the power to the fixture by turning the breaker
off or removing the fuse from the fuse box.
Your fixture is made from quality materials that will last many years with minimum care. You may want to
periodically clean the diffuser, or interior of the fixture using a mild, non-abrasive glass cleaner and a soft cloth.
DO NOT use solvents, or cleaners containing abrasive agents. When cleaning the inside of the fixture, make sure
you have the power turned off, and do not spray liquid cleaner directly onto the LEDs, LED driver or wiring.
ARCHIPELAGO LIGHTING | MONTCLAIR, CA (866) 912-3220 FAX (909) 627-2887 www.archipelagolighting.com
2
Mounting to wood
Drill a 1/16 in. diameter pilot hole in the
ceiling. Make sure to fasten the combo
wood-machine end into the metal hook.
Tighten the hook screw into the wood.
D
|
INSTALLATION INSTRUCTIONS
3
Attaching the light to the
chain
Install one header of chain to the hook
on the fixture body. Repeat
this step on the other side of the
fixture.
B
C
2
Locking the fixture to ceiling
With each fixture installation, insert additional
screw in ceiling opposite screw installed in
Church Key hole. This will prevent the fixture from
accidently sliding of screw mounting.
Screw
"Church Key"
hole
Please check with your local inspector to insure this mounting
method meets local requirements.
|
2
LED SHOP/UTILITY LIGHT
M
O
D
E
L
L
E
D
S
- L
9/4/7.5/40/4RM
4
Attaching the chain to
the ceiling
Install the pendant to the screw,tight-
ened by hand.Hang the fixture body
by placing one chain set over each
hook that has been installed on the
ceiling.Adjust chains to level light.
The fixture must hang at least 3 in.
from the ceiling.
Screw
|