Digilent chipKIT DP32 참조 매뉴얼 - 페이지 6

{카테고리_이름} Digilent chipKIT DP32에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Digilent chipKIT DP32 10 페이지. Board
Digilent chipKIT DP32에 대해서도 마찬가지입니다: 참조 매뉴얼 (18 페이지)

페이지 인쇄

chipKIT™ DP32™ Board Reference Manual

The minimum high-voltage output of the PIC32 microcontroller is rated at 2.4V when sourcing 12mA of current.

When driving a high impedance input (typical of CMOS logic), the output high voltage will typically be close to

3.3V. Some 5V devices will recognize this voltage as a logic high input, and some will not. You will have to read the

datasheet for the 5V parts you are using to ensure that 3.3V will satisfy the logic high conditions for the part. Many

5V logic devices will work reliably with 3.3V inputs.

4.3

Input/Output Connections

The DP32 board provides all 19 I/O pins of the PIC32MX250F128B microcontroller to through-hole points on the

PCB.

The PIC32 microcontroller can source 10mA with a minimum VOH of 3V and sink 15mA with a maximum VOL of

.4V on all digital I/O pins. The maximum current that can be sourced or sunk across all I/O pins simultaneously is

+/- 200mA. For more detailed specifications, refer to the PIC32MX1XX/2XX Data Sheet available from the

Microchip web site.

The DP32 uses logical pin numbers to identify digital I/O pins. Pins 0 through 8 are located on J4, counting up from

the square pad of J4. Pins 9 through 18 are located on J3, counting up from the square pad. In addition, several of

these I/O pins share functionality with other devices on the board. See table 1 in appendix A for more information.

Pins 15 and 16 are shared with the crystal for the internal oscillator, and are not typically usable. Pin 6 is shared

with the Analog Temperature Sensor. Pin 8 is shared with the onboard Potentiometer. Pins 4 and 5 are shared with

the USB Data+ and Data- signals. Pin 0 is shared with the USBID function, but removing jumper 1 clears this

conflict. Pins 9, 18, 7, and 10 are used for the SPI EEPROM device if it is loaded, on its Chip Select, Master

Out/Slave In, Serial Clock, and Master In/Slave Out lines respectively.

In addition to the digital I/O, there are Analog inputs available on the board, called A0 through A8. These pins are

shared on digital pins 6 through 14.

4.4

Peripheral I/O Functions

C: Synchronous serial interface. The I2C1 interface is available on pins 2 and 3. When using the I

necessary to set JP4 and JP5 such that pull-ups are present on the bus. This is accomplished by moving the jumpers

to pins 2 and 3 on each jumper, the default setting.

User LEDs: Pins 11 (LD4), 12 (LD3), 13 (LD2), and 14 (LD1) are shared between the through-hole connection and the

LED. Driving the pin high turns the LED on, driving it low turns it off.

User Buttons: Pins 1 (BTN3) and 17 (BTN2/PGM) are shared between a through-hole connection and a push

button. Pushing the button drives the input high. Releasing it brings the input low.

External Interrupts: Only INT0 is hard-mapped on the microcontroller. It is connected to pin 1. The other external

interrupts are accessible via PPS described below.

Reset: The Reset button is utilized to bring the MCLR pin low on the microcontroller, thus restarting the currently

loaded sketch. If the user wishes to reprogram the device, refer to section 3.1 for program mode instructions.

4.5

Peripheral Pin Select

An advanced feature of the PIC32MX1xx/2xx family of microcontrollers is the ability to re-map the locations of

peripheral devices. MPIDE does the default mapping.

Other product and company names mentioned may be trademarks of their respective owners.

C interface, it is

Page 6 of 9