Archos 100 series 사용자 설명서 - 페이지 7

{카테고리_이름} Archos 100 series에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Archos 100 series 13 페이지. Digital video recorder for archos jukebox multimedia (jbm 20) and for archos video av 100 and 300 series
Archos 100 series에 대해서도 마찬가지입니다: 사용자 설명서 (6 페이지)

페이지 인쇄

Recording with the DVR 100 on the AV300 series

Pre-record Screen

Setup Parameters

During Recording

1. On the pre-record screen, you should

see movement on the sound level bar

indicating that sound will be recorded.

Adjust the sound level by moving the

joystick to the left or right. Before

starting the recording, you can adjust

the recording parameters via middle

function button Settings.

Click on

Hide Bar to hide the video recording

overlay information.

2. In most situations, the DVR will

work fine without the user having to

adjust the settings.

However, by

clicking on the middle function button,

you have access to a number of

parameters that you can change before

you start the recording. See the table

below for descriptions.

Click any

function button to return to the pre-

record screen.

Click on the PLAY/PAUSE

button to start the recording. While

recording, you will see the length of

time of the recording in the top right of

the screen as well as a red "record"

indicator. Click on the PLAY/PAUSE

button again to pause the recording.

Click on the STOP/ESC

button to

stop the recording.

The AV300 will

take a few seconds to complete the

proper saving of the .AVI video file.

To make a video recording,

• Select Video Corder on the main menu screen.

• You will see the video image to record on the screen (if there is no video input into the DVR,

you will see a message "No Input Signal". Make sure that you are feeding the DVR with a

video source such as your television or a video cassette player.

• Click on the center function button Settings to make adjustments before you start the video

recording.

Rename

Allows you to change the filename before the recording begins.

Source

Composite, S-Video, Auto. You can choose which video input you want the

DVR to use. Normally, with a good video signal, you can set it to Auto, and the

DVR will scan the two inputs to see which one is receiving video.

Format

Auto, 4:3, 5:3, 16:9, 2.35. This is the aspect ratio of the screen that the DVR

will record. You can set this manually, but in most cases you can just leave it on

Auto.

Pictures/sec

High, Low. If you choose High, the DVR will record at 30 frames per second in

the North American NTSC standard and 25 frames per second in European PAL

standard. On low, it will record at 15 frames/sec and 12.5 frames/sec (half speed).

Bitrate

500 kb/s, 1000 kb/s, 1500kb/s, 2000 kb/s. Use this to set the encoding quality

(similar to the idea of JPEG image quality settings). The higher the encoding

rate, the higher the image quality but also the more hard drive space is used.

Brightness

Use this to increase or decrease the recorded image brightness

Contrast

Use this to increase or decrease the recorded image contrast

Saturation

Use this to de-emphasize or saturate the colors in the recorded image

Hue

Use this to change the color spectrum in the recorded image

Reset

Change the above settings to the AV300 default settings

• Once you have finished changing the parameters, click any function button to return to the pre-

record screen.

• Concerning the video standard, the DVR will automatically recognize if the incoming video

signal is NTSC (American), SECAM, or PAL (European). There is no need to set anything.

You will see the signal type, as well as the selected aspect ratio on the top left of the pre-record

screen.

• Move the joystick left and right to adjust the sound input level. Too far to the right will often

give a overdriven distorted quality. Too far to the left may make for a very soft sound. Try a

few recordings to get a sense of what is the best sound level. Do not let the headphone volume

fool you. That can be adjusted with the up/down of the joystick.

• Click on the PLAY/PAUSE

button to start recording and then later click on the STOP/ESC

to stop the recording.

• You can click on the PLAY/PAUSE

Click it again in order to recommence the recording.

• If you would like to make a recording in another folder instead of the default "Video" folder, go

to the desired folder via the main Video icon, then click on the lower function button Record.

button during the recording to pause the recording.